Panasonic KX-MB2061CXB Service Manual page 123

11.1.3. Service Function Table
Code Function
501 Pause time set
507 V34 transmission start speed
508 V34 reception start speed
511 VOX sense
514 Bell signal detect time
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
527 V.8 function select
529 Call Service Clear
550 Memory clear
551 ROM check
553 Monitor on FAX
select
554 Modem test
555 Scanner test
556 Motor test
557 LED test
558 LCD test
561 KEY test
567 T0 timer
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection
time set
573 Remote turn-on ring number set
574 Dial tone detect check
590 FAX auto redial time set
Set Value
1: 3s (Short)
2: 5s (Long)
0: Disable
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
0: Disable
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
1:High 2:Low 1, 2
X 100msec
1:2100 Hz
2:1100 Hz
1:ON 2:OFF
1:ON 2:OFF
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1:OFF 2:ON
communication 1:OFF
2:PHASE B
3:ALL
X second
1:61%
2:67%
3:63%
X number of
times
X second
X number of
rings
1: ON 2: OFF 1, 2
X number of
times
Effective Default
Range
1, 2 1 ----------
0~8 1 If the code 527 is set at 2, the code 507 and 508
work.
0~8 1 If the code 527 is set at 2, the code 507 and 508
work.
1 When the TAM (or EXT TAM) does not stop record-
ing the ICM because noise is detected on the tele-
phone line, change this setting to "LOW".
1~9 6 ----------
1, 2 1 See How To Output The Journal Report (P.183).
1, 2 1 See How To Output The Journal Report (P.183).
1, 2 1 The resolution reverts to the default when transmis-
sion is complete.
1~4 1 Set RX equalizer to automatic mode.
1~4 1
1, 2 2
Refer to Memory Clear Specification (P.125).
See Test Functions (P.119).
1~3 1 Sets whether to monitor the line signal with the
unit's speaker during FAX communication or not.
See Test Functions (P.119).
See Test Functions (P.119).
0 See Test Functions (P.119).
See Test Functions (P.119).
See Test Functions (P.119).
See Test Functions (P.119).
001~255 052 Sets a higher value when the response from the
other party needs more time during automatic FAX
transmission.
1~3 1 Sets the % break of pulse dialing according PBX.
00~99 05 Selects the number of times that ITS is redialed
(not including the first dial).
001~255 185 Sets the interval of ITS redialing.
00~99 10 Sets the number of rings before the unit starts to
operate TAM in the TEL mode.
2 ----------
00~99 05 Selects the number of redial times during FAX com-
munication (not including the first dial).
123
KX-MB2061CXB/KX-MB2061CX2/KX-MB2062CXB
Remarks