Toshiba V Series User Manual page 116

Appendix C Table of Trace Information
No. Event Level
C00D Daughter Major
board failure
diagnosis
error
Memory
C101 E 2 Major
PROM
failure
formatting
error
4102 Code Major
memory failure
update/
storage error
4103 Code Major
memory failure
update/
storage error
C103 E 2 Major
PROM
failure
code memory
clear error
C105 E 2 Major
PROM file
failure
clear error
C106 Code Major
memory DL failure
error
C
C107 Flash ROM Major
BCC check failure
error
C108 Flash ROM Major
BCC check failure
error
C110 Memory R/W Major
check error failure
C111 Memory R/W Major
check error failure
C112 Data memory Major
parity error failure
C113 Memory lost Major
failure
C114 Data memory Major
ECC error failure
(Uncorrectabl
e)
6116 Data memory Caution
ECC error
(Correctable)
C117 Memory Major
parity check failure
error
102
Execution
Timing Diagnosis
status
Periodical Error rundown
diagnosis
Error rundown Abnormality has
been detected
2
during E PROM
formatting.
Continued Code memory
cannot be stored
2
in E PROM.
Continued Code memory
cannot be
updated or stored
due to excessive
number of writing
operations in
2
E PROM.
Error rundown Abnormality has
been detected
2
during E PROM
code memory
clear operation.
Error rundown Code memory file
cannot be
cleared.
Initialization Error rundown Abnormality has
diagnosis been detected
during
downloading of
code data from
2
E PROM to
memory.
Initialization Error rundown Error has been
diagnosis detected in the
flash ROM BCC
calculation result.
Periodical Error rundown Error has been
diagnosis detected in the
flash ROM BCC
calculation result.
Initialization Error rundown Error has been
diagnosis detected in
memory write/
read comparison
check result.
Periodical Error rundown Error has been
diagnosis detected in
memory write/
read comparison
check result.
During user Error rundown Parity error has
task been detected
execution during data
memory access.
Initialization Error rundown User information
diagnosis area memory loss
has been
detected.
Interruption Error rundown Data memory
ECC error
(uncorrectable)
has been
detected.
Interruption Continued Data memory
ECC error
(correctable) has
been detected.
Initialization Error rundown Error has been
diagnosis detected by
memory read
parity check.
Task Address Aux1 Aux2
Status Status
(Hexadecima (Hexadeci
l code) mal code)
Off-line Status Status
During
Program
downloa
d
During
program
downloa
d
Status Status
Off-line
Status Status
BCC Block
number
BCC Block
number
Parity
detection
address
Status
(Hexadecima
l code)
Status
(Hexadecima
l code)
model 3000 Loop Controller L3 User's Manual - Basic Hardware -
Aux3 Cause Actions to be taken
Number of For CPU card with Replace and reboot CPU
retry daughter board, module, or contact our service
operations daughter board status staff.
was read incorrectly.
2 2
Failure of E PROM Format E PROM again and
Status reboot CPU. If CPU does not
(-1: Short of good boot, replace and reboot CPU
block module. Or contact our service
-2: FAT information 2
staff. E PROM has been
write error
formatted at factory.
-3: Code memory file
registration error)
2 Replace and reboot CPU
Failure of E PROM
module, or contact our service
staff.
2 Replace and reboot CPU
Failure of E PROM
module, or contact our service
staff.
Status 2 Replace and reboot CPU
Failure of E PROM
module. Before rebooting,
Status
conduct memory clear and batch
(-1: Zero write error
download. Or contact our
-2: Abnormal FAT
service staff.
block read
-3: FAT block not
registered)
Formatting is
necessary for
-3: FAT block not
registered.
2 Replace and reboot CPU
Failure of E PROM
module, or contact our service
staff.
Status 2 Replace reboot CPU module.
Failure of E PROM
Before rebooting, conduct
Status
memory clear and batch
(-1: Read error
download. Or contact our
-2: FAT block read
service staff.
error
-3: FAT block not
registered)
Formatting is
necessary for
-3: FAT block not
registered.
Number of Failure of flash ROM Replace and reboot CPU
error module, or contact our service
occurrences staff.
Number of Failure of flash ROM Replace and reboot CPU
error module, or contact our service
occurrences staff.
Defective RAM Replace and reboot CPU
content module, or contact our service
staff.
Defective RAM Replace and reboot CPU
content module, or contact our service
staff.
Defective program When program fallback has
memory If error been set, fall back target
occurs 10 or more program with control continued.
times during one task When program fallback has not
execution, error been set, error rundown occurs.
rundown or program Replace and reboot CPU
fallback results. module, or contact our service
staff.
CPU was left without Load program from engineering
parity, or defective tool, and reboot CPU module. If
RAM content. memory cannot be restored after
program loading, replace and
reboot CPU module, or contact
our service staff.
Defective RAM Replace and reboot CPU
content module, or contact our service
staff.
Transient failure of If this error occurs frequently,
RAM content replace and reboot CPU module,
or contact our service staff.
Defective RAM Replace and reboot CPU
content module, or contact our service
staff.