Fujitsu WSYA050ML3 Design & Technical Manual page 104

Line Access
S Function input H3
0: None, 1: Op'mode change zones + DHW, 2: Optg mode changeover DHW, 3: Op'mode
changeover zones, 4: Op'mode changeover zone 1, 5: Op'mode changeover zone 2, 6: Op'mode
changeover zone 3, 8: Error/alarm message, 9: Consumer request VK1, 10: Consumer request
VK2, 11: Release swi pool source heat, 13: Release swi pool solar, 14: Operating level DHW, 15:
Operating level HC1, 16: Operating level HC2, 17: Operating level HC3, 18: Room thermostat HC1,
5960
19: Room thermostat HC2, 20: Room thermostat HC3, 21: DHW fl ow switch, 24: Pulse count, 26:
Dewpoint monitor, 27: Flow temp setp incr hygro, 30: Swi-on command HP stage 1, 35: Status info
suppl source, 36: Charg prio DHW sol fuel boil, 43: Ventilation switch 1, 44: Ventilation switch 2, 45:
Ventilation switch 3, 50: Flow measurement Hz, 51: Consumer request VK1 10 V, 52: Consumer
request VK2 10 V, 54: Pressure measurement 10 V, 55: Humidity measurement 10 V, 56: Room
temp 10 V, 59: Flow measurement 10 V, 60: Temp measurement 10 V, 61: Air quality measurement
10 V
5963 S Input value 1 H3
5964 S Function value 1 H3
5965 S Input value 2 H3
5966 S Function value 2 H3
S Function input EX1
0: None, 1: Electrical utility lock E6, 2: Low-tariff E5, 4: Overload source E14, 5: Pressure switch
source E26, 6: Flow switch source E15, 7: Flow switch consumers E24, 8: Manual defrost E17, 9:
5980
Common fault HP E20, 10: Fault soft starter E25, 12: Low-pressure switch E9, 13: High-pressure
switch E10, 14: Overload compressor 1 E11, 15: Error/alarm message, 16: Mains supervision E21,
18: Pressure diff defrost E28, 19: Pres sw source int circ E29, 20: Flow sw source int circ E30, 21:
Smart grid E61, 22: Smart grid E62, 25: Optg mode change HCs, 26: DHW push
5981 S Contact type input EX1
S Function input EX2
0: None, 1: Electrical utility lock E6, 2: Low-tariff E5, 4: Overload source E14, 5: Pressure switch
source E26, 6: Flow switch source E15, 7: Flow switch consumers E24, 8: Manual defrost E17, 9:
5982
Common fault HP E20, 10: Fault soft starter E25, 12: Low-pressure switch E9, 13: High-pressure
switch E10, 14: Overload compressor 1 E11, 15: Error/alarm message, 16: Mains supervision E21,
18: Pressure diff defrost E28, 19: Pres sw source int circ E29, 20: Flow sw source int circ E30, 21:
Smart grid E61, 22: Smart grid E62, 25: Optg mode change HCs, 26: DHW push
5983 S Contact type input EX2
5985 S Contact type input EX3
Readjustment collector
6098 S
sensor
6100 S Readjustment outside sensor -3...3°C
Central setpoint
6117 S
compensation
6120 S Frost protection plant
6201 S Reset sensors
6205 S Reset to default parameters
6220 S Software version (RVS)
6300 S Info 1 OEM
6301 S Info 2 OEM
When an installation is started up, the hydraulic indoor unit diagram pre-setting for that installation
must be entered.
3-13. Installation configuration functions
Function Setting range or display
NC (Normally-closed contact)
NO (Normally-opened
contact)
NC (Normally-closed contact)
NO (Normally-opened
contact)
NC (Normally-closed contact)
NO (Normally-opened
contact)
-20...20°C
1...100°C
On, Off
No, Yes
No, Yes
0...99
0...65535
0...65535
- (03-46) -
Setting Factory
increment setting
None
0
0
10
100
1
NO
Low-tariff E5
NC
NO
0°C
0.1°C 0°C
5°C
On
No
No
---
---
---
3. Function table