Dell PowerVault 124T LTO-3 User Manual page 49

BF Picker Jammed Cartridge Error
Servo Motor Error Types
C0 Motor Error
C1 Motor SW Error
C2 Motor HW Error
C3 Motor Seg Error
C4 Motor Position Error
C5 Motor Direction Error
C6 Motor Runaway Error
C7 Motor Corrupt
C8 Motor Acceleration Error
C9 Motor Sense Noise
CA Motor Seek Error
CB Motor Skipped Step
C C Motor Stalled
CD Motor Jammed
CE Motor Translation Pin Jammed
Error
CF Motor Asynchronous Stop
Magazine Hardware Error Types
D0 Magazine Eject Failed
D1 Magazine Present Sensor Bad
D2 Magazine Cam Position Sensor
Bad
D3 Magazine Sensor 1 Bad
D4 Magazine Sensor 2 Bad
D5 Magazine Flag Missing
D6 Magazine Flag Bad
D7 Slot Zero Not Found
D8 Multiple Slot Zero Detected
D9 Magazine Step Tolerance Error
DA Magazine Calibration Lost
DB Magazine Lost
DC Magazine Position Error
DD Magazine Slot Type Invalid
DE Magazine Slot (Gross) Position
Error
DF Magazine Jammed Error
System Event Types
E8 Time Zone Update Event
Power cycle the autoloader.
l
Run the Random Moves test from either the Remote Management Unit (RMU) or the Operator Control
l
Panel (OCP).
Note: The Random Moves test requires a minimum of two cartridges present within the autoloader.
If all previous steps fail, contact support.dell.com.
l
Insure that the autoloader is resting on a solid flat surface, or mounted level in a rack unit.
l
Power cycle the autoloader.
l
Run the Random Moves test from either the Remote Management Unit (RMU) or the Operator Control
l
Panel (OCP).
Note: The Random Moves test requires a minimum of two cartridges present within the autoloader.
Check support.dell.com for PowerVault 124T firmware updates.
l
If all previous steps fail, contact support.dell.com.
l
Insure that the autoloader is resting on a solid flat surface, or mounted level in a rack unit.
l
Remove and re-insert the magazine. Verify that the magazine slides freely in and out of the magazine
l
bay.
Verify that the magazine clicks and locks in place when fully inserted.
l
Power cycle the autoloader and retry the operation.
l
If all previous steps fail, contact support.dell.com.
l
Insure that the autoloader is resting on a solid flat surface, or mounted level in a rack unit.
l
Remove and re-insert the magazine. Verify that the magazine slides freely in and out of the magazine
l
bay.
Verify that the magazine clicks and locks in place when fully inserted.
l
Power cycle the autoloader and run the Magazine Test from the Operator Control Panel.
l
If all previous steps fail, contact support.dell.com.
l
Magazine errors may occur if the magazine sensor cannot detect cartridge carrier flags during magazine
rotation. This may be caused by an issue with a cartridge carrier flag, a sensor problem, a physically jammed
magazine, or a sensor alignment issue caused by a mis-inserted magazine.
Insure that the autoloader is resting on a solid flat surface, or mounted level in a rack unit.
l
Remove and inspect the magazines one at a time. Turn the white thumbwheels on each magazine
l
and insure that the carriers move freely at least one full rotation in each direction.
Verify that carrier flags are present on all slots and slot 1 has the unique (longer) carrier flag.
l
Insure that the sensors protruding from the picker into the magazine bays are free of debris, and
l
'float' in and out freely when pushed by hand.
Carefully re-insert the magazine straight into the magazine bay. Be careful to avoid twisting or
l
biasing the magazine up or down.
Power cycle the autoloader.
l
Run the Magazine Test from the operator control panel.
l
If all previous steps fail, contact support.dell.com.
l
User updated the time zone setting. No action required.
Get other manuals https://www.bkmanuals.com