Dell PowerVault 124T LTO-3 User Manual page 54

Drive TAflag[28] Power The tape drive power consumption is
Consumption outside the specified range.
TapeAlert Log Entry:
0000001000000000
Drive TAflag[29] Drive Preventive maintenance of the tape drive is
Maintenance required.
TapeAlert Log Entry:
0000000800000000
Drive TAflag[30] Hardware The tape drive has a hardware fault.
A
TapeAlert Log Entry:
0000000400000000
Drive TAflag[31] Hardware B The tape drive has a hardware fault.
TapeAlert Log Entry:
0000000200000000
Drive TAflag[32] Interface The tape drive has a problem with the
application client interface.
TapeAlert Log Entry:
0000000100000000
Drive TAflag[33] Eject Media The operation has failed.
TapeAlert Log Entry:
0000000080000000
Drive TAflag[34] Download The firmware download has failed because
Fail you have tried to use the incorrect firmware
for this tape drive.
TapeAlert Log Entry:
0000000040000000
Drive TAflag[35] Drive Environmental conditions inside the tape
Humidity drive are outside the specified humidity
range.
TapeAlert Log Entry:
0000000020000000
Drive TAflag[36] Drive Environmental conditions inside the tape
Temperature drive are outside the specified temperature
range.
TapeAlert Log Entry:
0000000010000000
Drive TAflag[37] Drive The voltage supply to the tape drive is
Voltage outside the specified range.
TapeAlert Log Entry:
0000000008000000
Drive TAflag[38] Predictive A hardware failure of the tape drive is
Failure predicted.
TapeAlert Log Entry:
0000000004000000
Drive TAflag[39] Diagnostics The tape drive may have a hardware fault
Required
TapeAlert Log Entry:
0000000002000000
Drive TAflag[50] Lost Media statistics have been lost at some time
Statistics in the past.
TapeAlert Log Entry:
0000000000004000
Drive TAflag[51] Tape The tape directory on the tape cartridge just
Directory Invalid at Unload unloaded has been corrupted. File search
performance will be degraded.
TapeAlert Log Entry:
0000000000002000
Drive TAflag[52] Tape The tape just unloaded could not write its
System Area Write Failure system area successfully.
TapeAlert Log Entry:
0000000000001000
Drive TAflag[53] Tape The tape system area could not be read
System Area Read Failure successfully at load time.
Power consumption of the tape
drive is outside specified range.
The drive requires preventative
maintenance (not cleaning).
The drive has a hardware fault
that requires reset to recover.
The drive has a hardware fault
that is not read/write related or
requires a power cycle to
recover.
The drive has identified an
interface fault.
Error recovery action
Firmware download failed.
Drive humidity limits exceeded.
Cooling problem.
Drive voltage limits exceeded.
Predictive failure of drive
hardware.
The drive may have a hardware
fault that may be identified by
extended diagnostics (i.e., SEND
DIAGNOSTIC command).
Drive or library powered on with
tape loaded
Error preventing the tape
directory being updated on
unload.
Write errors while writing the
system area on unload.
Read errors while reading the
system area on load
Get other manuals https://www.bkmanuals.com
Check the tape drive user's manual for device
specific preventive maintenance tasks.
Eject the tape.
l
Reset the drive.
l
Restart the operation.
l
Power cycle the tape drive.
l
Restart the operation.
l
Check the SCSI interface cables,
l
terminator, and all connections.
Restart the operation.
l
Eject the tape or magazine.
l
Insert the tape or magazine again.
l
Restart the operation.
l
Obtain the correct firmware and try again.
Run extended diagnostics to verify and
l
diagnose the problem.
Check the tape drive user's manual for
l
device specific instructions on running
extended diagnostic tests.
Clean drive.
l
Retry operation.
l
The tape directory can be rebuilt by reading
all the data.
Copy data to another tape cartridge.
l
Discard the old cartridge.
l
Copy data to another tape cartridge.