Yamaha Electone STAGEA ELB-01 Owner's Manual page 54

Parameter
LFO Freq. 0.00 – 39.7 Hz
AM Depth 0 – 127
PM Depth 0 – 127
Input Mode Mono/Stereo
LFO Depth 0 – 127
L/R Depth 0 – 127
F/R Depth 0 – 127
3
No. Type
08 AUTO PAN
09 XG AT PAN
10 EP AUTO PAN
Parameter
LFO Freq. 0.00 – 39.7 Hz
L/R Depth 0 – 127
F/R Depth 0 – 127
Pan L<->R
L->R
L<-R
Lturn
Rturn
L/R
ROTARY SPEAKER
This popular effect (used mainly for electronic organ
sounds) recreates the rich, animated pulsing sound of
a rotating speaker horn.
No. Type
01 XG ROTARY SP
02 ROTARY SP 1
03 ROTARY SP 2
04 ROTARY SP 3
05 ROTARY SP 4
Parameter
EQ LowFreq.
EQ Low Gain
EQ Hi.Freq.
54 ELB-01 Owner's Manual
Range Description
Determines the tremolo speed.
Determines the amount of volume
change.
Determines the amount of pitch
change in the sound.
Determines the input
configuration.
Determines the depth of the
Tremolo effect.
Determines the depth of panning
between the left and right
channels.
Front/rear. Determines the depth
of the front and rear panning
effect. This controls both level
and pitch at the same time.
Value Description
Determines the frequency of the
Auto Pan effect, or how fast the
sound shifts between the left and
right channels.
Determines the depth of the left/
right panning effect.
Determines the depth of the front/
rear panning effect. This controls
both level and pitch at the same
time.
Determines the Auto Pan type.
("L<->R" is a sine wave and "L/R"
is a sawtooth wave.)
Value Description
32 – 2.0k Hz Determines the central frequency
of the low frequency range that is
boosted or cut.
-12 – +12 dB Determines the amount over
which the low frequency range is
boosted or cut.
500 – 16k Hz Determines the central frequency
of the high frequency range that
is boosted or cut.
Parameter Value
EQ Hi.Gain -12 – +12 dB
DISTORTION
This effect adds distortion to the sound.
No. Type
01 DIST HARD
02 DIST SOFT
03 OVERDRIVE
04 XG DIST
05 XG AMP SIM
Parameter Value
Drive 0 – 127
Amp. Type Off
Stack
Combo
Tube
LPF Cutoff 1.0 – 18k Hz
Thru
OutputLevel 0 – 127
EQ Low Gain -12 – +12 dB
EQ Mid.Gain -12 – +12 dB
Dry/Wet D63>W – D<W63
WAH
This uses an automatic up/down filter sweep to
change the timbre of the sound, producing a "wah-
wah" sound.
No. Type
01 AUTO WAH
02 XG AUTO WAH
03 TOUCH WAH 1
04 TOUCH WAH 2
05 CLAVI TC WAH
06 EP TOUCH WAH
Parameter Value
LFO Freq. 0.00 – 39.7 Hz
LFO Depth 0 – 127
Cutoff 0 – 127
Resonance 1.0 – 12.0
Description
Determines the amount over
which the high frequency range is
boosted or cut.
Description
Determines the amount or degree
of distortion in the sound.
Determines the type of amplifier
that is simulated.
Determines the cutoff frequency
of the low pass filter. Frequencies
above this value are cut or filtered
out.
Determines the level or volume of
the processed sound.
Determines the amount of EQ
boost or cut in the low frequency
range.
Determines the amount of EQ
boost or cut in the mid frequency
range.
Determines the balance of the
original sound and the effect
sound.
Description
Determines the speed of the Wah
effect.
Determines the depth of the Wah
effect.
Determines the central frequency
that the wah filter acts upon.
Determines the frequency
bandwidth (around the central
frequency set in Cutoff above)
that the wah filter affects.