Set Worker Switches (Wsw) And Print Worker Switch Setting Data (Function Code: 10, 11) - Brother DCP-L5500D Service Manual

1.3.4 Set worker switches (WSW) and print worker switch setting data
(function code: 10, 11)
[1] Set worker switches (function code: 10)
<Function>
The worker switches shown in the table below can be used to set the function to satisfy various
requirements. These switch settings can be changed using the keys on the control panel.
The worker switches are factory set to conform to the laws and regulations of the country the
machine is shipped to. Do not change these settings unless necessary.
WSW No.
WSW01 Dial pulse setting
WSW02 Tone signal setting
WSW03 PABX mode setting
WSW04 Transfer facility setting
WSW05 1st dial tone and busy tone detection
[Redial/Pause] key and 2nd dial tone
WSW06
detection
WSW07 Dial tone setting 1
WSW08 Dial tone setting 2
WSW09 Protocol definition 1
WSW10 Protocol definition 2
WSW11 Busy tone setting
WSW12 Signal detection condition setting
Modem setting
WSW13
WSW14 AUTO ANS facility setting
WSW15 Redial facility setting
WSW16 Function setting 1
WSW17 Function setting 2
WSW18 Function setting 3
WSW19 Transmission speed setting
WSW20 Overseas communication mode setting
WSW21 TAD setting 1
WSW22 ECM and call waiting caller ID
WSW23 Communication setting
WSW24 TAD setting 2
WSW25 TAD setting 3
WSW26 Function setting 4
WSW27 Function setting 5
WSW28 Function setting 6
WSW29 Function setting 7
WSW30 Function setting 8
WSW31 Function setting 9
WSW32 Function setting 10
WSW33 Function setting 11
Function setting 12
WSW34
Function setting 13
WSW35
Function setting 14
WSW36
WSW37 Function setting 15
WSW38 V.34 transmission settings
V.34 transmission speed
WSW39
WSW40 V.34 modem settings
WSW41 ON-duration of the scanning light source
WSW42 Internet mail settings
* Refer to the separate manual for details of worker switches.
Function
5-8
WSW No.
WSW43 Function setting 16
WSW44 Speeding up scanning-1
WSW45 Speeding up scanning-2
WSW46 PC power monitoring and parallel port settings
WSW47 Switching between high- and full-speed USB
USB setup latency
WSW48
WSW49 End-of-copying beep
WSW50 SDAA setting
WSW51 Function setting 17
WSW52 Function setting 18
WSW53 Function setting 19
WSW54 Function setting 20
Interval for regular developing bias value
WSW55
correction
WSW56 Function setting 21
WSW57 Function setting 22
WSW58 Function setting 23
WSW59 Function setting 24
WSW60 Function setting 25
WSW61 Scanning light intensity to judge to be stable 1
WSW62 Scanning light intensity to judge to be stable 2
WSW63 Function setting 26
WSW64 Language / default paper size setting
WSW65 Paper support setting
WSW66 Change of the setting is prohibited
WSW67 Change of the setting is prohibited
WSW68 Change of the setting is prohibited
WSW69 Change of the setting is prohibited
WSW70 Change of the setting is prohibited
WSW71 Change of the setting is prohibited
WSW72 Change of the setting is prohibited
WSW73 Change of the setting is prohibited
WSW74 ADF stop control
WSW75 Switch back ejection distance
Set the limit for the number of documents
WSW76 to be ejected in reverse order for single-
side scanning from ADF
Set the limit for the number of documents
WSW77 to be ejected in reverse order for duplex
scanning from ADF
Recording stop function when the drum
WSW78
reaches the end of life
WSW79 Function setting 27
WSW80 Copying speed control function
Changing emulation function enable/
WSW81
disable setting
WSW82 AirPrint Icon No. setting
WSW83 Change of the setting is prohibited
WSW84 Change of the setting is prohibited
Function
Confidential