Set Worker Switches (Wsw) And Print Worker Switch Setting Data (Function Code: 10, 11) - Brother DCP-7080 Service Manual

1.3.5 Set worker switches (WSW) and print worker switch setting data
(function code: 10, 11)
[1] Set worker switches (WSW) (function code: 10)
<Function>
The worker switches shown in the table below can be used to set the function to satisfy various
requirements. These switch settings can be changed using the keys on the control panel.
The worker switches are factory set to conform with the laws and regulations of the country
the machine is shipped to. Do not change these settings unless necessary.
WSW No.
WSW01 Dial pulse setting
WSW02 Tone signal setting
WSW03
PABX mode setting
WSW04 Transfer facility setting
WSW05 1st dial tone and busy tone detection
[Redial/Pause] key and 2nd dial tone
WSW06
detection
WSW07 Dial tone setting 1
WSW08 Dial tone setting 2
WSW09
Protocol definition 1
WSW10 Protocol definition 2
WSW11 Busy tone setting
WSW12
Signal detection condition setting
WSW13 Modem setting
WSW14 AUTO ANS facility setting
WSW15
Redial facility setting
Function setting 1
WSW16
WSW17 Function setting 2
WSW18
Function setting 3
WSW19 Transmission speed setting
WSW20 Overseas communication mode setting
WSW21
TAD setting 1
WSW22 ECM and call waiting caller ID
WSW23 Communication setting
WSW24
TAD setting 2
WSW25 TAD setting 3
WSW26 Function setting 4
WSW27
Function setting 5
WSW28 Function setting 6
WSW29 Function setting 7
WSW30
Function setting 8
WSW31 Function setting 9
WSW32 Function setting 10
WSW33
Function setting 11
WSW34
Function setting 12
WSW35 Function setting 13
WSW36
Function setting 14
Function setting 15
WSW37
V.34 transmission settings
WSW38
V.34 transmission speed
WSW39
* Refer to the separate manual for details of worker switches.
Function
5-9
WSW No.
WSW40 V.34 modem settings
WSW41 ON-duration of the scanning light source
WSW42
Internet mail settings
WSW43 Function setting 16
WSW44 Speeding up scanning-1
Speeding up scanning-2
WSW45
WSW46 PC power monitoring and parallel port settings
WSW47 Switching between high- and full-speed USB
WSW48
USB setup latency
WSW49 End-of-copying beep
WSW50 SDAA setting
WSW51
Function setting 17
WSW52 Function setting 18
WSW53 Function setting 19
WSW54
Function setting 20
Interval for regular developing bias
WSW55
value correction
WSW56 Function setting 21
WSW57
Function setting 22
WSW58 Function setting 23
WSW59 Function setting 24
WSW60
Function setting 25
WSW61 Scanning light intensity to judge to be stable 1
WSW62 Scanning light intensity to judge to be stable 2
WSW63
Function setting 26
WSW64 Language / default paper size setting
WSW65 Paper support setting
WSW66
Change of the setting is prohibited
WSW67 Change of the setting is prohibited
WSW68 Change of the setting is prohibited
WSW69
Change of the setting is prohibited
WSW70 Change of the setting is prohibited
WSW71 Change of the setting is prohibited
WSW72
Change of the setting is prohibited
WSW73
Change of the setting is prohibited
WSW74 ADF stop control
WSW75
Switch back ejection distance
Set the limit for the number of
WSW76
documents to be ejected in reverse
order for single-side scanning from ADF
Set the limit for the number of
WSW77
documents to be ejected in reverse
order for duplex scanning from ADF
Recording stop function when the drum
WSW78
reaches the end of life
Function
Confidential