Motorola APX 1000 Basic Service Manual page 14

viii List of Figures
Figure 6-38. Transmitter Test Pattern Screen (UHF1)............................................................................. 6-28
Figure 6-39. Transmitter Test Pattern Screen (UHF2)............................................................................. 6-29
Figure 6-40. Transmitter Test Pattern Screen (700/800 MHz)................................................................. 6-29
Figure 6-41. Transmitter Test Pattern Screen (900 MHz)........................................................................ 6-30
Figure 8-1. APX 2000/ APX 4000/ APX 4000Li Partial Exploded View................................................... 8-2
Figure 8-2. Lifting up the latch ................................................................................................................. 8-4
Figure 8-3. Removing the Battery ........................................................................................................... 8-5
Figure 8-4. Removing the Antenna ......................................................................................................... 8-5
Figure 8-5. Removing the Multi Function Knob ....................................................................................... 8-6
Figure 8-6. Removing the Thumb Screw................................................................................................. 8-7
Figure 8-7. Disengage the Chassis ......................................................................................................... 8-8
Figure 8-8. Remove the Chassis Assembly ............................................................................................ 8-8
Figure 8-9. Remove the chassis screws.................................................................................................. 8-9
Figure 8-10. Remove the Secondary Shield Assembly ............................................................................. 8-9
Figure 8-11. Remove the Main O-Ring at the antenna holder................................................................. 8-10
Figure 8-12. Lift up the Main Board from the Chassis ............................................................................. 8-10
Figure 8-13. Unplug the Back Kit Flex connectors .................................................................................. 8-11
Figure 8-14. Disengage the Shroud ........................................................................................................ 8-11
Figure 8-15. Remove the Shroud ............................................................................................................ 8-11
Figure 8-16. Remove the Keypad Retainer Screws ................................................................................ 8-12
Figure 8-17. Remove the Keypad Retainer ............................................................................................. 8-12
Figure 8-18. Unplug the Front Kit Flex and Back Kit Flex Connectors .................................................... 8-13
Figure 8-19. Remove the Keypad Board ................................................................................................. 8-13
Figure 8-20. Disengage the Keypad........................................................................................................ 8-14
Figure 8-21. Remove the Keypad............................................................................................................ 8-14
Figure 8-22. Serviceable Components - Main Board Assembly ............................................................. 8-15
Figure 8-23. Serviceable Components - Chassis Assembly................................................................... 8-16
Figure 8-24. Serviceable Components - Main Housing .......................................................................... 8-18
Figure 8-25. Servicing the Multi Function Knob....................................................................................... 8-19
Figure 8-26. Assemble the RF Board ...................................................................................................... 8-20
Figure 8-27. Assemble the Main O-Ring at Antenna Holder ................................................................... 8-20
Figure 8-28. Assemble the Secondary Shield Assembly......................................................................... 8-21
Figure 8-29. Torque in the Chassis Screws............................................................................................. 8-21
Figure 8-30. Assemble the Keypad ......................................................................................................... 8-22
Figure 8-31. Plug in the Front Kit Flex Connector ................................................................................... 8-23
Figure 8-32. Plug in the Back Kit Flex Connectors.................................................................................. 8-23
Figure 8-33. Place Keypad Retainer over the Keypad Board.................................................................. 8-24
Figure 8-34. Torque in the Keypad Retainer Screws............................................................................... 8-24
Figure 8-35. Assemble the Shroud.......................................................................................................... 8-25
Figure 8-36. Slide chassis assembly into Front Housing......................................................................... 8-25
Figure 8-37. Assemble Back Kit and Front Kit together .......................................................................... 8-25
Figure 8-38. Engaging Hook and Seating Cover..................................................................................... 8-26
Figure 8-39. Securing the Cover ............................................................................................................. 8-26
Figure 8-40. Reassemble the Multi Function Knob ................................................................................. 8-27
Figure 8-41. Attaching the Antenna......................................................................................................... 8-28
Figure 8-42. Assemble the Vacuum Port Seal......................................................................................... 8-28
Figure 8-43. Assemble the Ventilation Label ........................................................................................... 8-28
Figure 8-44. Assemble the Bottom Label ................................................................................................ 8-29
Figure 8-45. Attaching Battery - Slide into Position ................................................................................ 8-29
Figure 8-46. Attaching Vacuum Test Fixture............................................................................................ 8-32
Figure 10-1. APX 2000/ APX 4000/ APX 4000Li Front Kit Exploded View ............................................. 10-2
Figure 10-2. APX 2000/ APX 4000/ APX 4000Li Back Kit Exploded View.............................................. 10-4