Hitachi SJ700-2 Series Instruction Manual page 125

(4) C parameters
Display
Function name
code
C001 Terminal [1] function
C002 Terminal [2] function
C003 Terminal [3] function
C004 Terminal [4] function
C005 Terminal [5] function
C006 Terminal [6] function
C007 Terminal [7] function
C008 Terminal [8] function
C011 Terminal [1] active state
C012 Terminal [2] active state
C013 Terminal [3] active state
C014 Terminal [4] active state
C015 Terminal [5] active state
C016 Terminal [6] active state
C017 Terminal [7] active state
C018 Terminal [8] active state
C019 Terminal [FW] active state
Range of setting
1 (RV: Reverse RUN), 2 (CF1: Multispeed 1 setting),
3 (CF2: Multispeed 2 setting), 4 (CF3: Multispeed 3
setting), 5 (CF4: Multispeed 4 setting), 6 (JG: Jogging),
7 (DB: external DC braking), 8 (SET: Set 2nd motor
data), 9 (2CH: 2-stage acceleration/deceleration), 11
(FRS: free-run stop), 12 (EXT: external trip), 13 (USP:
unattended start protection), 14: (CS: commercial power
source enable), 15 (SFT: software lock), 16 (AT: analog
input voltage/current select), 17 (SET3: 3rd motor
control), 18 (RS: reset), 20 (STA: starting by 3-wire
input), 21 (STP: stopping by 3-wire input), 22 (F/R:
forward/reverse switching by 3-wire input), 23 (PID: PID
disable), 24 (PIDC: PID reset), 26 (CAS: control gain
setting), 27 (UP: remote control UP function), 28 (DWN:
remote control DOWN function), 29 (DWN: remote
control data clearing), 31 (OPE: forcible operation), 32
(SF1: multispeed bit 1), 33 (SF2: multispeed bit 2), 34
(SF3: multispeed bit 3), 35 (SF4: multispeed bit 4), 36
(SF5: multispeed bit 5), 37 (SF6: multispeed bit 6), 38
(SF7: multispeed bit 7), 39 (OLR: overload restriction
selection), 40 (TL: torque limit enable), 41 (TRQ1: torque
limit selection bit 1), 42 (TRQ2: torque limit selection bit
2), 43 (PPI: P/PI mode selection), 44 (BOK: braking
confirmation), 45 (ORT: orientation), 46 (LAC: LAD
cancellation), 47 (PCLR: clearance of position
deviation), 48 (STAT: pulse train position command input
enable), 50 (ADD: trigger for frequency addition [A145]),
51 (F-TM: forcible-terminal operation), 52 (ATR:
permission of torque command input), 53 (KHC:
cumulative power clearance), 54 (SON: servo-on), 55
(FOC: pre-excitation), 56 (MI1: general-purpose input 1),
57 (MI2: general-purpose input 2), 58 (MI3:
general-purpose input 3), 59 (MI4: general-purpose input
4), 60 (MI5: general-purpose input 5), 61 (MI6:
general-purpose input 6), 62 (MI7: general-purpose input
7), 63 (MI8: general-purpose input 8), 65 (AHD: analog
command holding), 66 (CP1: multistage position settings
selection 1 ), 67 (CP2: multistage position settings
selection 2), 68 (CP3: multistage position settings
selection 3), 69 (ORL: Zero-return limit function), 70
(ORG: Zero-return trigger function), 71 (FOT: forward
drive stop), 72 (ROT: reverse drive stop), 73 (SPD:
speed / position switching), 74 (PCNT: pulse counter),
75 (PCC: pulse counter clear), no (NO: no assignment)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
8 - 9
Chapter 8 Appendix
Minimum Setting during Updating during
operation operation
unit
(allowed or not) (allowed or not)
− × ○
− × ○
− × ○
− × ○
− × ○
− × ○
− × ○
− × ○
− × ○
− × ○
− × ○
− × ○
− × ○
− × ○
− × ○
− × ○
− × ○