Firmware Update" Configuration Page - ABB 83342-500 Operating Instructions Manual

Operating Instructions
ABB-Welcome
Pos: 62 /#Neustruktur#/Online-Dokumentation (+KNX)/Überschriften (--> Für alle Dokumente <--)/2. Ebene/M - O/Konfigurationsseite "Firmware Update" @ 35\mod_1362553067374_15.docx @ 284908 @ 21211222121212221121122222222222222221111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111122222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222232223322222222222222 @ 1
6.11

"Firmware Update" configuration page

Pos: 63 /#Neustruktur#/Online-Dokumentation (+KNX)/Projektierung/Türkommunikation/Busch-Welcome II/Menü Firmware Update - 83341 @ 36\mod_1370935346604_15.docx @ 296824 @ 2111111111112222222222222222222222222222111111111112121122212121222112112222222222222222111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111112222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222211111111111112232223322222222222222 @ 1
Fig. 28: "Firmware Update" configuration page
The IP gateway has the option to manually update the device software.
Note
Device updates are not normally required and should only be carried out for troubleshooting
purposes. To update the device, please contact your electrical installer.
Note
Before updating the firmware, always check if the update bears a date more recent that the
software already installed. See also the section "Version information".
Pos: 64 /#Neustruktur#/Online-Dokumentation (+KNX)/Steuermodule - Online-Dokumentation (--> Für alle Dokumente <--)/++++++++++++ Seitenumbruch ++++++++++++ @ 9\mod_1268898668093_0.docx @ 52149 @ 22212121222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222 @ 1
Note
All settings of the IP gateway will been reset to the factory settings during the update. Please first
note down the details specified under basic settings and device settings.
Pos: 63 /#Neustruktur#/Online-Dokumentation (+KNX)/Projektierung/Türkommunikation/Busch-Welcome II/Menü Firmware Update - 83341 @ 36\mod_1370935346604_15.docx @ 296824 @ 2111111111112222222222222222222222222222111111111112121122212121222112112222222222222222111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111112222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222211111111111112232223322222222222222 @ 1
Perform the following steps to update your device, if necessary.
1. Get the latest software from your electrical installer.
2. Log into the Web-Interface of the IP-Gateway with the username "admin" and the associated password.
3. Open menu item firmware update and upload the .tar/.img file.
4. After the file has been sent to the IP-Gateway and installed on the device, the IP-Gateway is reachable again
via the browser.
ATTENTION: This process may take up to 10 minutes. The device must not be disconnected from the power
supply during this period.
5. Afterwards, the IP-Gateway can be taken into use again.
The user name and password have been reset to the factory settings admin / admin .Assign a new password
if necessary.
Re-enter the configuration data (basic settings, device settings).
Set the time zone.
Configuration for IP Gateway
— 38 —