Mitsubishi Electric Y Series Manual page 80

SPECIFICATIONS
80
WY-Series
PQHY-P YSLM-A1
Model
Power source
Cooling capacity
(Nominal)
Power input
Current input
EER
Temp. range of Indoor
cooling Inlet water
Heating capacity
(Nominal)
Power input
Current input
COP
Temp. range of Indoor
heating Inlet water
Indoor unit Total capacity
connectable Model / Quantity
Sound pressure level
(measured in anechoic room)
Sound power level
(measured in anechoic room)
Refrigerant piping Liquid pipe
diameter Gas pipe
Set Model
Circulating water Water fl ow rate
Pressure drop
Operating
volume range
Compressor Type
Starting method
Motor output
Case heater
External fi nish
External dimension HxWxD
Protection High pressure protection
devices Inverter circuit (COMP.)
Compressor
Refrigerant Type x original charge
Net weight
Heat exchanger
Water volume in
plate
Water pressure
Max.
Optional parts
Notes:
*1,*2 Nominal conditions
Cooling
Heating
*The ambient temperature of the heat source unit needs to be kept below 40ºCD.B.
*The ambient relative humidity of the heat source unit needs to be kept below 80%.
*The heat source unit should not be installed at outdoor.
*Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
*Be sure to provide interlocking for the unit operation and water circuit.
*Nominal condition *1,*2 are subject to JIS B8615-2.
*Due to continuing improvement, above specifi cation may be subject to change without notice.
PQHY-P850YSLM-A1
3-phase 4-wire 380-400-415 V 50/60 Hz
*1
kW
kcal / h
*1 BTU / h
327,600
kW
A 30.4-28.9-27.8
kW / kW
W.B. 15.0~24.0°C (59~75°F)
°C 10.0~45.0°C (50~113°F)
*2
kW
kcal / h
*2 BTU / h
368,500
kW
A 31.2-29.6-28.5
kW / kW
D.B. 15.0~27.0°C (59~81°F)
°C 10.0~45.0°C (50~113°F)
50~130% of heat source unit capacity
P10~P250/2~50
dB <A>
dB <A>
mm (in.) 19.05 (3/4) Brazed
mm (in.) 41.28 (1-5/8) Brazed
PQHY-P450YLM-A1
m 3 / h 7.20 + 7.20
L/min 120 + 120
cfm 4.2 + 4.2
kPa 44
m 3 / h 4.5 + 4.5 ~ 11.6 + 11.6
Inverter scroll hermetic compressor
Inverter
kW 11.6
kW –
Galvanized steel sheets
mm 1,450 x 880 x 550
in. 57-1/8 x 34-11/16 x 21-11/16
High pressure sensor, High pressure switch at 4.15 MPa (601 psi) High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
Over-heat protection, Over-current protection
Over-heat protection
R410A x 6.0 kg (14 lbs)
kg (lbs) 214 (472)
plate type
L 5.0
MPa 2.0
Heat Source Twinning kit: CMY-Y200VBK2
Joint: CMY-Y102SS/LS-G2, CMY-Y202, 302S-G2
Header: CMY-Y104, 108, 1010-G
Indoor Inlet water temperature
27ºCD.B./19ºCW.B.
30ºC (86ºF)
(81ºFD.B./66ºFW.B.)
20ºCD.B. (68ºFD.B.) 20ºC (68ºF)
96.0
82,600
18.03
5.32
108.0
92,900
18.49
5.84
56
71.5
PQHY-P400YLM-A1
44
Inverter
10.7
–
Galvanized steel sheets Galvanized steel sheets
1,450 x 880 x 550
57-1/8 x 34-11/16 x 21-11/16 57-1/8 x 34-11/16 x 21-11/16
Over-heat protection
R410A x 6.0 kg (14 lbs) R410A x 6.0 kg (14 lbs)
214 (472)
plate type
5.0
2.0
Pipe length Level diff erence
7.5m (24-9/16ft.)
PQHY-P900YSLM-A1
3-phase 4-wire 380-400-415 V 50/60 Hz
101.0
86,900
344,600
19.38
32.7-31.0-29.9
5.21
15.0~24.0°C (59~75°F)
10.0~45.0°C (50~113°F)
113.0
97,200
385,600
19.74
33.3-31.6-30.5
5.72
15.0~27.0°C (59~81°F)
10.0~45.0°C (50~113°F)
50~130% of heat source unit capacity
P10~P250/2~50
57
73
19.05 (3/4) Brazed
41.28 (1-5/8) Brazed
PQHY-P450YLM-A1 PQHY-P450YLM-A1
7.20 + 7.20
120 + 120
4.2 + 4.2
44
4.5 + 4.5 ~ 11.6 + 11.6
Inverter scroll hermetic compressor
Inverter Inverter
11.6
–
Galvanized steel sheets
1,450 x 880 x 550 1,450 x 880 x 550
57-1/8 x 34-11/16 x 21-11/16
Over-heat protection, Over-current protection
Over-heat protection Over-heat protection
R410A x 6.0 kg (14 lbs)
214 (472) 214 (472)
plate type plate type
5.0
2.0
Heat Source Twinning kit: CMY-Y200VBK2
Joint: CMY-Y102SS/LS-G2, CMY-Y202, 302S-G2
Header: CMY-Y104, 108, 1010-G
0m (0ft.)
44
11.6
–
5.0
2.0