Mitsubishi Electric 800 Series Instruction Manual page 82

Pr. group Pr.
Starting magnetic pole
C185 721
position detection pulse width
Starting resistance tuning
C188 720
compensation coefficient
C200 450 Second applied motor
C201 453 Second motor capacity
C202 454 Number of second motor poles
C203 51 Rated second motor current
C204 456 Rated second motor voltage
C205 457 Rated second motor frequency
Second motor maximum
C206 743
frequency
C207 744 Second motor inertia (integer)
Second motor inertia
C208 745
(exponent)
Second motor auto tuning
C210 463
setting/status
Second motor online auto
C211 574
tuning
C220 458 Second motor constant (R1)
C221 459 Second motor constant (R2)
Second motor constant (L1) /
C222 460
d-axis inductance (Ld)
Second motor constant (L2) /
C223 461
q-axis inductance (Lq)
C224 462 Second motor constant (X)
Second motor excitation
C225 455
current
Second motor torque current/
C226 860
Rated PM motor current
Second motor induced voltage
C230 738
constant (phi f)
C231 739 Second motor Ld decay ratio
C232 740 Second motor Lq decay ratio
Second motor protection
C233 746
current level
Second motor induced voltage
C235 1413
constant (phi f) exponent
Second motor starting
C282 741 resistance tuning
compensation coefficient 1
Second motor magnetic pole
C285 742
detection pulse width
Starting resistance tuning
C288 737
compensation coefficient 2
 A: Application parameters
Parameters for the setting of a specific application.
Pr. group Pr.
A100 278 Brake opening frequency
A101 279 Brake opening current
Refer
Name
to page
318
309
304
309,
318
309,
318
206,
309,
318
309,
318
309,
318
318
318
318
309,
318,
369
325
309,
318,
369
309
309,
318
309,
318
309
309
309,
318
318
318
318
318
318
318
318
318
Refer
Name
to page
330
330
Pr. group Pr.
Brake opening current
A102 280
detection time
A103 281 Brake operation time at start
A104 282 Brake operation frequency
A105 283 Brake operation time at stop
Brake opening current
A108 639
selection
Brake operation frequency
A109 640
selection
Automatic acceleration/
A110 292
deceleration
Stop-on-contact control
A200 270
selection
Stop-on contact excitation
A205 275 current low-speed scaling
factor
PWM carrier frequency at stop-
A206 276
on contact
A300 592 Traverse function selection
A301 593 Maximum amplitude amount
Amplitude compensation
A302 594
amount during deceleration
Amplitude compensation
A303 595
amount during acceleration
A304 596 Amplitude acceleration time
A305 597 Amplitude deceleration time
A600 759 PID unit selection
A601 131 PID upper limit
A602 132 PID lower limit
A603 553 PID deviation limit
A604 554 PID signal operation selection
Integral stop selection at
A607 1015
limited frequency
A610 128 PID action selection
A611 133 PID action set point
PID control automatic
A612 127
switchover frequency
A613 129 PID proportional band
A614 130 PID integral time
A615 134 PID differential time
Output interruption detection
A621 575
time
Output interruption detection
A622 576
level
Output interruption cancel
A623 577
level
PID set point/deviation input
A624 609
selection
PID measured value input
A625 610
selection
C42
A630 PID display bias coefficient
*1
(934)
C43
A631 PID display bias analog value
*1
(934)
3.4 Parameter list (by function group number)
Refer
Name
to page
330
330
330
330
330
330
177,
330
334
334
334
337
337
337
337
337
337
352
339,
355
339,
355
339
339
339
339,
355
339,
355
339
339,
355
339,
355
339,
355
339
339
339
339,
355
339,
355
352
352
81
3. Parameters
1
2
3
4
5
6
7
8
9
10