Table of Contents
Advertisement
Maintenance
Drain fi lter
Remove dust.
1
Perform the "Spin" operation. (P.26)
(Drain water in the drum.)
2
Turn the power on, and prepare a container such as a
cup to receive water discharged from the pump hose.
3
Open the drain fi lter cover.
If the drain fi lter cover comes off (How to attach →P.6)
4
Pull out the pump hose and
remove the cap to drain the water
into the cup.
5
Turn the "Tip of knob
" to the "●"
position slowly.
If the buzzer beeps, do not remove.
(Large amount of water spills over.)
6
Confi rm no water is left,
and pull it out.
7
Remove dust.
If the 2 rubber seals are misaligned,
restore them to the original positions.
(To prevent water leak)
CAUTION
Do not
Large amount of
remove during
water will spill over.
operation.
30
Drain fi lter/Dry fi lter
Cap
Drain
fi lter
Pump
hose
After removing dust
(1) A lign "
" with "●",
and insert.
Face the
"TOP"
mark up.
(2) T ighten securely
until "
" meets
" ".
Drain
fi lter
(3) R eplace the cap and
pump hose to the
Brush,
original position.
etc.
Attention
Do not use the drain fi lter
Before removing, be
in a loosened state.
sure to run the "Spin"
("U18" is displayed and
operation. (P.26)
operation is not possible.)
Attention
Do not use gritty cleanser, thinner, benzine, alcohol, kerosene, etc.
If detergent or softener is attached to the main unit (especially door, operation
panel and touch panel), immediately wipe it off with a wrung-out towel, etc.
Before maintenance,
(Peeling of print, damage to resin, metal corrosion or malfunction may occur.)
be sure to turn the power off ,
In particular, if liquid concentrated detergent is attached to the resin part, it
may crack.
and remove the power plug!
Note that if detergent, etc. is attached to the door hinge part (metal part),
metal corrosion may occur.
Dry fi lter
Remove dust.
When the "Wash" operation (P.26) is performed with warm
water, wipe off water droplets.
The "Clean Filter" indication notifi es that cotton-like dust has been accumulated in the dry fi lter.
(A buzzer beeps when the door is opened after operation has fi nished.)
The indicator may blink even after one-time operation. This is not a malfunction.
1
Remove the
dry fi lter.
Do not remove during
operation.
2
Remove cotton-like dust,
and wipe it clean with a
wrung-out towel, etc.
Do not scrub with force.
(The fi lter may be
Wrung-out
broken.)
towel, etc.
3
Remove dust from
the dry fi lter (inside).
Dry fi lter (inside)
If "U04" is displayed, remove the dry fi lter (inside) and wash with water.
Running water
Wash while rubbing
it with the pads of
fi ngers, and dry
Dry fi lter
completely.
(inside)
(Do not scrub with brush, etc.)
4
Attach the dry fi lter.
Attention
(Securely set inside.)
Do not operate the appliance with the dry fi lter removed. (Drying
performance may deteriorate or dust may stir up)
After removing the fi lter, do not wash the
main unit side with water or put foreign
objects into it.
If dust is stuck to
the fi lter, wash
with lukewarm
water and dry
well.
Warm water
Remove cotton-like dust
and wipe it clean with a
wrung-out towel, etc.
Removing
Attaching
Click
(2) Push
(1) Insert
31
Hide quick links:
Advertisement
Table of Contents
