Mitsubishi Electric Lossnay LGH-RX5-E Series Manual page 79

12.2 Setting the Day of the
Week and Time
■ Use this screen to change the current day of the week and time setting.
Note:
The day and time will not appear if clock use has been disabled or the simple timer
has activated at Function Selection of remote controller.
Dot display
<How to Set the Day of the Week and Time>
2
CLOCK] button A to show display
1. Press the or [
ON/OFF (DAY)] button 9 to set the day.
2. Press the [
* Each press advances the day shown at
CLOCK] button A as necessary to set the time.
3. Press the appropriate [
* As you hold the button down, the time (at
intervals, then in 10-minute intervals, and then in 1-hour intervals.
4. After making the appropriate settings at Steps 2 and 3, press the
lock in the values.
Note:
Your new entries at Steps 2 and 3 will be cancelled if you press the BACK button
button 4.
before pressing the
5. Press the BACK button 2 to complete the setting procedure. This will return the
display to the standard control screen, where
and time.
* To change the time or day of the week, start from Step 1 above.
Note:
If you are using two remote controllers, setting the time and day of the week in one
remote controller will cause the new setting to be applied to the other as well.
Operation
1. Starting the Lossnay unit
2. Setting the ventilation mode
3. Selecting the fan speed
4. Selecting the Extra Low fan
1 2
speed* *
5. Stopping the Lossnay unit
* 1 If you press a button for a feature that is not installed at the Lossnay unit, the remote controller will display the "NOT AVAILABLE" message.
* 2 If set to "24-hour Ventilation", pressing the [
Extra low fan speed mode. To stop operation, press the [
Day of the Week &
Time display
3
Day of the Week Setting
4
Time Setting
2 .
3 : SUN MON ... FRI TSA
4 ) will increment first in minute
1 will now show the newly set day
Dot display
Function selector button
Relevant button Relevant display items
Operation lamp
"High"
"HEAT EX." non-automatic
"Low" "Extra High"
"Extra Low"
Operation lamp
ON/OFF] button will cause this to be displayed in the dot display "24HR VENTILATION", and the operation will switch to
ON/OFF] button twice within 3 seconds, or press and hold the [
12.3 Using the Remote Controller
Typical System Setup
In either case, up to two remote controllers can be used.
Two remote controller operation
• When two individual remote controllers have been installed, the most recent
control signals will be given priority.
Independent operation of the Lossnay unit:
Interlocked operation with an air conditioners, etc.:
Power
supply
Power
supply
button 4 to
2
Press the [ ON/OFF] button and confirm that the Operation lamp turns on.
Press the Function selector button: Each time it is pressed, the corresponding display will
change in accordance with the sequence [HEAT EX.] (non-automatic) --> [BY-PASS] (non-
automatic) --> [AUTO].
Press the Fan Speed Adjustment button to select either Low or High (Extra High) fan
speed. High and Extra-High can be selectable by initial setting.
Press the "Extra Low" fan speed button.
Extra low operation will begin. Pressing the Fan Speed Adjustment button will cause the
fan speed to revert to its original speed (before the Extra low mode began).
Pressing the Extra Low fan speed button again will return operation to Extra low mode.
Press the [ ON/OFF] button.*
(Press the [ ON/OFF] button to turn off the Operation lamp.)
Lossnay
Remote controller(s)
Up to two remote controllers can be used
Power supply
Lossnay
Remote controller(s)
Indoor unit
Operation switch
for the external
Lossnay
device
A maximun of up to 15 Lossnay units
may be connected.
ON/OFF button
Fan Speed Adjustment button
"Extra Low" fan speed button
Sequence
2
ON/OFF] button for 5 seconds.
The Lossnay can
be controlled same
as in independent
Lossnay operation.
Power supply
The Lossnay can
be started and
stopped via external
equipment.
C-79