Huawei EchoLife HG8110 Service Manual page 217

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
4.
Step 4 Add an ONT on the OLT.
The ONT is connected to the GPON port of the OLT through optical fibers. The service can be
configured only after an ONT is successfully added on the OLT.
Two ONTs are connected to GPON port 0/1/1. The ONT IDs are 1 and 2, the SNs are
6877687714852900 and 6877687714852901, the management mode is OMCI, and ONT line
profile 10 and service profile 10 are bound to the two ONTs.
1.
2.
Issue 02 (2011-12-08)
NOTE
The port vlan command is use for specifying a port VLAN and managing the attribute of the UNI port
on the ONT remotely. This command is applicable for only the L2 service (L2 Internet access service)
when the ONT functions as a bridge device. When the ONT functions as a gateway device, the
configuration of the port VLAN is implemented on the ONT Web page, NMS, or U2560 server.
huawei(config)#ont-srvprofile gpon profile-id 10
huawei(config-gpon-srvprofile-10)#ont-port eth 4 pots 2 catv 1
huawei(config-gpon-srvprofile-10)#port vlan eth 1 10
After the configurations are complete, run the commit command to make the configured
parameters take effect.
huawei(config-gpon-srvprofile-10)#commit
huawei(config-gpon-srvprofile-10)#quit
(Optional) Configure an alarm profile.
l The ID of the default GPON alarm profile is 1. The thresholds of all the alarm parameters
in the default alarm profile are 0, which indicates that no alarm is reported.
l In this example, the default alarm profile is used, and therefore the configuration of the
alarm profile is not required.
l Run the gpon alarm-profile add command to configure an alarm profile, which is used
for monitoring the performance of an activated ONT line.
Add an ONT offline.
If the password or SN of an ONT is obtained, you can run the ont add command to add
the ONT offline.
huawei(config)#interface gpon 0/1
huawei(config-if-gpon-0/1)#ont add 1 1 sn-auth 6877687714852900 omci ont-
lineprofile-id 10 ont-srvprofile-id 10
huawei(config-if-gpon-0/1)#ont add 1 2 sn-auth 6877687714852901 omci ont-
lineprofile-id 10 ont-srvprofile-id 10
Automatically find an ONT.
If the password or SN of an ONT is unknown, run the port portid ont-auto-find command
in the GPON mode to enable the ONT auto-find function of the GPON port. Then, run the
ont confirm command to confirm the ONT.
huawei(config)#interface gpon 0/1
huawei(config-if-gpon-0/1)#port 1 ont-auto-find enable
huawei(config-if-gpon-0/1)#display ont autofind 1
//After this command is executed, the information about all ONTs connected
to
the GPON port through the optical splitter is displayed.
------------------------------------------------------------------------
Number
F/S/P
Ont SN
Password
VenderID
Ont Version
Ont SoftwareVersion : V1R002C06
Ont EquipmentID
Ont autofind time
------------------------------------------------------------------------
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
: 1
: 0/1/1
: 6877687714852900
:
: HWTC
: 120D0010
: 247
: 2010-12-10 14:59:10
3 Configuration
209