Tightening Torque Specifications; Tightening Torque List - Komatsu PC220LC -8 Operation & Maintenance Manual

MAINTENANCE

TIGHTENING TORQUE SPECIFICATIONS

TIGHTENING TORQUE LIST

If nuts, bolts, or other parts are not tightened to the specified torque, it will cause looseness or damage to the tightened parts, and
this will cause failure of the machine or problems with operation.
Always pay careful attention when tightening parts.
Unless otherwise specified, tighten the metric nuts and bolts to the torque shown in the table below.
If it is necessary to replace any nut or bolt, always use a Komatsu genuine part of the same size as the part that was
replaced.
Thread Width
diameter across
Target value
of bolt flats
Nm kgm
(a)(mm) (b)(mm)
6 10 13.2 1.35
8 13 31 3.2
10 17 66 6.7
12 19 113 11.5
14 22 172 17.5
16 24 260 26.5
18 27 360
20 30 510 52.3
22 32 688 70.3
24 36 883
27 41 1295 132.5
30 46 1720 175.0
33 50 2210 225.0
36 55 2750 280.0
39 60 3280 335.0
Apply the following table for Hydraulic Hose.
Width
Hose
across
nominal Target valve
flat
number
Nm kgm
a (mm)
02 19 44 4.5
22 74 7.5
03
24 78 8.0
04 27 103 10.5
05 32 157 16.0 115.7 128-186 13.0-19.0 94.0-137.4
06 36 216 22.0 159.1 177-245 18.0-25.0 130.2-180.8
Tightening torque
Service limit
lbft Nm kgm
9.8 11.8-14.7 1.2-1.5
23.1 27-34 2.8-3.5
48.5 59-74 6.0-7.5
83.2 98-123 10.0-12.5
126.6 153-190 15.5-19.5
191.7 235-285 23.5-29.5
37 267.6 320-400 33.0-41.0
378.3 455-565 46.5-58.0
508.5 610-765 62.5-78.0
90 651 785-980 80.0-100.0
958.4 1150-1440 118.0-147.0
1265.8 1520-1910 155.0-195.0
1627.4 1960-2450 200.0-250.0
2025.2 2450-3040 250.0-310.0
2423.1 2890-3630 295.0-370.0
Tightening torque
Service limit
lbft Nm kgm
32.5 35-54 3.5-5.5
54.2 54-93 5.5-9.5
57.9 59-98 6.0-10.0
75.9 84-132 8.5-13.5
CAUTION
lbft
8.7-10.8
20.3-25.3
43.4-54.2
72.3-90.4
112.1-141
170.0-213.4
238.7-296.6
336.3-419.5
452.1-564.2
578.6-723.3
853.5-1063.3
1121.1-1410.4
1446.6-1808.3
1808.3-2242.2
2133.7-2676.2
lbft
25.3-47.0
39.8-68.7
43.4-72.3
61.5-97.6
TIGHTENING TORQUE SPECIFICATIONS
4 - 13