Table of Contents
Advertisement
2
3
4
WARNING:
For your own safety,
lower
blade
or other
cL4t}ng
tool be!ow
table
surfacer
(H
btade
is tilted_
return
il to vertical
90% posi-
tion}.,
Always
fork
the switch
"OFF".
When
saw is not m use, _emove
key and keep it in a
safe
place_
Also_
#,, the
event
of a power
t
/ faiture
(a:t of Vour lilhls
go out} turn
swttch
off,
lock
it by
_emoving
the key,
This
wit
t prevent
the saw from starling
up again
when
!.. t2e.
............................................................
ELEVATION
HANDWHEEt
....
elevates
or
lowers
the
b!ade,
tum
c_ockwise
to elevate,
coun_,erclockwise
to k._wer.
T_LT HANDWHEEL..._i_ts
the blade for beve!
cutting.
Turn c_ockwise to ti_t toward
ieft, cocmte_.
c_ockwise to flit toward ri_._:}ht.
Wher_ the blade is thted to the kt}FT as far as il wi_i
go. it shouid
be a_ 45" ,_o me tab@ and the bevel
indic££o_ should
poir_t to 45"'.
NOTE:
There
are LIMIT
STOPS
inside the saw
wI_ ci_ prevent the Made from tilting beyond 45 '_to the
LE,_T ar_d 90" to _he RIGHT.
( See "ADJUSTMENTS
AND
ALiGNMBNTS"
5ecfioa
'BLADE
TIL[,
OR
',SQUAR!:.Nif:: SS OF BI..AD{:: TO TABLE').
R!P
FE}{CE
...
is locked ,'.,_ p}ace by tightening
the Lock Knob.
To move
the Fe;_ce, loosen
the
Knob and grasp
the Fence
wi{h one hand at the
front.
} _oies a_e provided
in _he Rip Fence {o, _ attaching
a
wood facing when using the Dado Head, or Molding
Head.
Select
a piece
of smooth
straight
wood approxi-.
mate!y
3/4 inch thick, at least as long as the Rip
Fence,
and at least
7-1/2
inches
wide
{high)
to
permit clamping
of Featherboards.
Attach it to the Fence with three Round Head #10
Wood Screws
2 inches _oP, g. To remove the facing,
loosen the screws,
s!ide _he facing forward
and putt
the screws through
the round
he;ca.
WOOD
FACING
"_%
/
///
ROUND
HEAD
/
t0
WOOD
SCREWS
MODEL
113.298090
!f you are making a rip type cut in material thinner
than 31!6 inch while _he Fence is positioned over the
depressed area of Table Extension, the facing shoutd
be attached to the Fence so that the bottom edge
33
touches
the top surface
of th.e Eixtensios
n this
case, the facing
mus_ be shorter
titan the Fence.
This wi_ prevent thin mater;al from sliding under the
Rip Fence
5
MITER
GAUGE
, . . head is !ocked in
t:×)sitior_ tot crosscutting
or mitering by t_ghte r_ing the
Lock K_,::,b ALWAYS
LOCK _T SECURELY
WHEN
tN USE.
Slots are provided
in tI_e Miter Gauge for at£aching
an Auxi!iary
Facir_g to make
it easier to Odt iong
pieces.
Be _x.'.,sitive Faci_.g does net irs_edere wth
the proper operation
of the Sawb!ade
Gua:d.
Setect a suitab!e piece of snK)oti_ straigh_ wood
dri_I
two ho_es through
it and attach it wi!h screws.
NOTE:
When bevel crosscutting,
attach Facing so
that it extends to the right of the Miter Gauge and use
the Miter Gauge
in the groove
to the right of She
b_ade.
...................LOCK
KNOB
,,
_- AUXILLARY
FACING
_,5 =:_ SLOT
......
6
7
BLADEGUARD..,
must a_waysbe in p!ace and
working properly for all thmosawm9 cuts. Tha_ is, ati
cuts whereby the blade cuts oompiete_y through the
workpiece.
q-o rein/dye the Guard for speciaI operations, loosen
the Wing Nuts and slide the Guard back and upward
off the Spreader Bracket. DO NOT DISTURB THE
SETTING OF THE SPREADER BRACKET.
Wher_ replacing
the Guard, slide the Spreader down
and
forward
between
the
Spreader
C_amp
and
S_reaaer Bracket until the bottom and rear edges oi
al{ three are even
Make sure both Wing Nuts are
hand t_ghtened securely.
TABLE
INSERT.
_ _is removabie 1or remewng
or installing
b_ades or other cumng Ioo_s
WARNING:
To avoid
injury due to accldentaI,
start,
turn
switch
"OFF"
and
remove
plug
}
from
power
source
outlet
before
removing
I
InserL
]
A Lower the blade below the table su_ace
B. Raise Blade Guard.
C. Loosen screw.
D, Lift insert from front end, and pull toward tront of
saw.
NEVER OPERATE
THE SAW W_THOUT THE
PROPER INSERT IN PLACE. Use the saw blade
insert when using a saw blade. Use the combination
DadoiMolding insert when using a Dado or Mol@ng
head.
Hide quick links:
Advertisement
Table of Contents
