Copy Performance - Sharp AL-2020 Service Manual

Section, item
Image forming Photoconductor
Charger
Developing
Cleaning
Fusing section Fusing system
Upper heat roller
Lower heat roller
Heater lamp
Electrical section Power source
Power consumption

3. Copy performance

Section, item
Copy magnification Fixed magnification
ratios
Zooming magnification
ratios
Manual steps (manual, photo)
Copy speed (CPM) First-copy time *1
(Approximately)
AB system
A4 (Landscape)
AB system
B5 (Landscape)
Inch system
8-1/2" x 11" (Landscape)
Max. continuous copy quantity
Void Void area
Image loss
Warm-up time
Power save mode reset time
Paper jam recovery time
*1: The first-copy time is measured after the power save indicator turns off following power on, using the document glass with the polygon rotat-
ing in the copy ready state and "Selection of copy start state" set to ON in the user programs (A4 (8-1/2" x 11"), paper fed from paper tray).
The first-copy time may vary depending on machine operating conditions and ambient conditions such as temperature.
Details
Type
Life
Charging system
Transfer system
Separation system
Developing system
Cleaning system
Type
Type
Type
Voltage
Power consumption
Voltage
Frequency
Max.
Average (during copying)
Average (stand-by)
Pre-heat mode
Auto power shut-off mode
Details
Same size
Same size
Same size
Leading edge
Trailing edge
Side edge void area
Leading edge
AL-2020/2035/2040/2050/2060 SPECIFICATIONS 2 - 2
OPC (30ø)
18k
Saw-tooth charging with a grid, / (-) scorotron discharge
(+) DC corotron system
(-) DC corotron system
Dry, 2-component magnetic brush development system
Counter blade system (Counter to rotation)
Heat roller system
Teflon roller
Silicon rubber roller
Halogen lamp
120V / 220 - 240V
800W
120V / 220 - 240V
Common use for 50 and 60Hz
Less than 1000W
350Wh/H or less (AL-2020/2035/2040)
380Wh/H or less (AL-2050/2060)
80Wh/H or less
25Wh/H or less (AL-2020/2035/2040)
28Wh/H or less (AL-2050/2060)
8.8W or less (AL-2020/2035/2040)
12.5W or less (AL-2050/2060)
AL-2020/2035/2040/2050/2060
4 Reduction + 3 Enlargement
(AB system: 25, 50, 70, 86, 100, 141, 200, 400%)
(Inch system: 25, 50, 64, 78, 100, 129, 200, 400%)
25 - 400% (376 steps in 1% increments)
50 - 200% when using SPF/RSPF (151 steps in 1% increments)
5 steps
AL-2020/2035/2040:
8.0 seconds (When user program 24 is set to OFF)
10.7 seconds
(paper: A4 (8-1/2" x 11"), exposure mode: AUTO, copy ratio: 100%)
AL-2050/2060:
8.0 seconds
20
20
20
99
1 - 4mm
4mm or less
0.5mm or more (per side)
4.5mm or less (total of both sides)
same size: 3.0mm or less (OC) / 4mm or less (SPF/RSPF)
Enlarge: 1.5mm or less (OC) / 3mm or less (SPF/RSPF)
Reduction (50%): 6.0mm or less (OC) / 8mm or less (SPF/RSPF)
0 sec. Immediately the ready lamp is lit.
0 sec. Immediately the ready lamp is lit.
0 sec.
∗
Jam recovery condition: Recovery time from 60 sec of door open.