Parameter Description Hart - ABB TZIDC Operating Instructions Manual

TZIDC DIGITAL POSITIONER | OI/TZIDC-EN REV. B
Parameter description HART®
Parameter Display Function
P1._ STANDARD
P1.0 ACTUATOR Actuator type
P1.1 AUTO_ADJ Automatic adjustment Autoadjust
P1.2 ADJ_MODE Auto adjust mode
P1.3 TEST Test
P1.4 FIND_DEV Find device
P1.5 EXIT Return
P2._ SETPOINT
P2.0 MIN_RGE Min setpoint range
P2.1 MAX_RGE Max setpoint range
P2.2 CHARACT Charact. curve
P2.3 ACTION Valve action
P2.4 SHUT_CLS Shut-off value 0%
P2.5 SHUT_OPN Shut off value 100%
P2.6 RAMP UP Set point ramp, up
P2.7 RAMP DN Set point ramp, down Setpoint ramp (down)
P2.8 EXIT Return
P3._ ACTUATOR
P3.0 MIN_RGE Min. of stroke range
P3.1 MAX_RGE Max. of stroke range
P3.2 ZERO_POS Zero position
P3.3 EXIT Return
P4._ MESSAGES
P4.0 TIME_OUT Control time out
P4.1 POS_SW1 Position switch 1
P4.2 POS_SW2 Position switch 2
P4.3 SW1_ACTV Switchpoint 1 enable
P4.4 SW2_ACTV Switchpoint 2 enable
P4.5 EXIT Return
P5._ ALARMS
P5.0 LEAKAGE Leakage detection
P5.1 SP_RGE Setpoint rng monitor
SENS_RGE
P5.2 Sens. range monitor
CTRLER
P5.3 Controller monitor
TIME_OUT
P5.4 Control time out
STRK_CTR
P5.5 Stroke counter
TRAVEL
P5.6 Travel counter
EXIT
P5.7 Return
Possible parameter setting
Actuator type LINEAR, ROTARY
Function
Automatic adjustment mode FULL,STROKE,CTRL_PAR, ZERO_POS, LOCKED
Test Function
Find device DISABLE, ONE TIME, CONTINOUS
Return to operating level Function
Min. setpoint range 4.0 to 18.4
Max. setpoint range 20.0 to 5.6
Characteristic curve LINEAR, 1:25, 1:50, 25:1, 50:1, USERD
Direction of action DIRECT, REVERSE
Shut-off value 0 % OFF, 0.1 to 45.0
Shut-off value 100% 55.0 to 100.0, OFF
Setpoint ramp (up) OFF, 0 to 200
OFF, 0 to 200
Return to operating level Function
Operating range, min. 0.0 to 90.0
Operating range, max. 100.0 to 10.0
Zero position CLOCKWISE, CTCLOCKWISE
Return to operating level Function
Dead band time limit OFF, to 200
Switching point SW1 0.0 to 100.0
Switching point SW2 0.0 to 100.0
Active direction SW1 FALL_BEL, EXCEED
Active direction SW2 FALL_BEL, EXCEED
Return to operating level Function
Leakage to actuator ACTIVE, INACTIVE
Outside the setpoint range ACTIVE, INACTIVE
Operating range exceeded ACTIVE, INACTIVE
Controller inactive ACTIVE, INACTIVE
Dead band time limit ACTIVE, INACTIVE
Movement counter ACTIVE, INACTIVE
Travel counter ACTIVE, INACTIVE
Return to operating level Function
37
Unit Factory setting
--- LINEAR
--- ---
FULL
--- INACTIVE
--- DISABLE
--- NV_SAVE
mA 4.0
mA 20.0
--- LINEAR
--- DIRECT
% 1.0
% OFF
--- OFF
--- OFF
--- NV_SAVE
% 0.0
% 100
--- CTCLOCKWISE
--- NV_SAVE
--- OFF
% 0.0
% 100.0
--- FALL_BEL
--- EXCEED
--- NV_SAVE
--- INACTIVE
--- INACTIVE
--- INACTIVE
--- INACTIVE
--- INACTIVE
--- INACTIVE
--- INACTIVE
--- NV_SAVE