GE AF-650 GP Programming Manual page 62

[62] Comparator 2
[63] Comparator 3
[64] Comparator 4
[65] Comparator 5
[70] Logic Rule 0
[71] Logic Rule 1
[72] Logic Rule 2
[73] Logic Rule 3
[74] Logic Rule 4
[75] Logic Rule 5
[80] SL Digital Output A
[81] SL Digital Output B
[82] SL Digital Output C
[83] SL Digital Output D
[84] SL Digital Output E
[85] SL Digital Output F
[120] Local reference active
[121] Remote reference active
[122] No alarm
[123] Start command active
[124] Running reverse
[125] Drive in hand mode
[126] Drive in auto mode
See par. group LC-1#. If Comparator 2 is evaluated as TRUE, the output will go high. Otherwise, it will be
low.
See par. group LC-1#. If Comparator 3 is evaluated as TRUE, the output will go high. Otherwise, it will be
low.
See par. group LC-1#. If Comparator 4 is evaluated as TRUE, the output will go high. Otherwise, it will be
low.
See par. group LC-1#. If Comparator 5 is evaluated as TRUE, the output will go high. Otherwise, it will be
low.
See par. group LC-4#. If Logic Rule 0 is evaluated as TRUE, the output will go high. Otherwise, it will be
low.
See par. group LC-4#. If Logic Rule 1 is evaluated as TRUE, the output will go high. Otherwise, it will be
low.
See par. group LC-4#. If Logic Rule 2 is evaluated as TRUE, the output will go high. Otherwise, it will be
low.
See par. group LC-4#. If Logic Rule 3 is evaluated as TRUE, the output will go high. Otherwise, it will be
low.
See par. group LC-4#. If Logic Rule 4 is evaluated as TRUE, the output will go high. Otherwise, it will be
low.
See par. group LC-4#. If Logic Rule 5 is evaluated as TRUE, the output will go high. Otherwise, it will be
low.
See par. LC-52 Logic Controller Action. The output will go high whenever the Logic Controller Action [38]
Set dig. out. A high is executed. The output will go low whenever the Logic Controller Action [32] Set dig.
out. A low is executed.
See par. LC-52 Logic Controller Action. The input will go high whenever the Logic Controller Action [39]
Set dig. out. A high is executed. The input will go low whenever the Logic Controller Action [33] Set dig.
out. A low is executed.
See par. LC-52 Logic Controller Action. The input will go high whenever the Logic Controller Action [40]
Set dig. out. A high is executed. The input will go low whenever the Logic Controller Action [34] Set dig.
out. A low is executed.
See par. LC-52 Logic Controller Action. The input will go high whenever the Logic Controller Action [41]
Set dig. out. A high is executed. The input will go low whenever the Logic Controller Action [35] Set dig.
out. A low is executed.
See par. LC-52 Logic Controller Action. The input will go high whenever the Logic Controller Action [42]
Set dig. out. A high is executed. The input will go low whenever the Logic Controller Action [36] Set dig.
out. A low is executed.
See par. LC-52 Logic Controller Action. The input will go high whenever the Logic Controller Action [43]
Set dig. out. A high is executed. The input will go low whenever the Logic Controller Action [37] Set dig.
out. A low is executed.
Output is high when par. F-02 Operation Method = [2] Local or when par. F-02 Operation Method = [0]
Linked to hand auto at the same time as the Keypad is in Hand mode.
Output is high when par. F-02 Operation Method = Remote [1] or Linked to hand/auto [0] while the
Keypad is in [Auto] mode.
Output is high when no alarm is present.
Output is high when there is an active Start command (i.e. via digital input bus connection or [Hand] or
[Auto]), and no Stop or Start command is active.
Output is high when the frequency converter is running counter clockwise (the logical product of the
status bits 'running' AND 'reverse').
Output is high when the frequency converter is in [Handmode] (as indicated by the LED light above [Hand]).
Output is high when the frequency converter is in [Hand] mode (as indicated by the LED light above [Auto]).
AF-650 GP Programming Guide
3
61