Siemens 6SN1123-1AA00-0DA2 Configuration Manual page 482

02.12
05.01
Line filter
Basic Line Filter, 7-231, 7-235
For I/R modules, 7-231
For UI modules, 7-231
Wideband Line Filter, 7-231
Wideband line filter, 7-232
Line fuses, 7-215
Line infeed, 6-141
Line supply connection, 1-26, 4-107, 4-115, 7-201
Line system configurations, 7-205
IT-line supply, 7-208
TN-C line supply, 7-206
TT line supply, 7-207
Load duty cycle definitions, 5-127
M
Main Spindle Drive
Master drive, 8-297
Slave drive, 8-297
Main switches, 7-226, 8-239
Master/slave operation, 8-297
Minimum cross–section for PE, 7-209
Module
ANA module, 4-112
Braking module, 1-26
Capacitor module, 1-26, 6-183
HLA module, 4-104
Infeed module, 1-26
Monitoring module, 1-26, 6-179
Overvoltage limiter module, 7-203
Power module, 1-26
VP module, 2-48
Modules
Braking module, 6-191
Overvoltage limiter module, 6-190, 7-203
Power module, 5-121
Monitoring module, 1-26, 6-142, 6-179
LED display, 6-181
Mode of operation, 6-181
Motor
Encoder, 3-64
Overview, 1-27
Protection, 3-63
Selection, 2-48, 3-63
with holding brake, 3-63
Motor changeover, 8-302
Motor encoder, 3-64
Motor holding brake, 4-90
Motor rotor position sensing, 3-68
Motor speed sensing, 3-68
Mounting and installing the modules, 2-45
N
NCSD Configurator, 1-29
© Siemens AG 2012 All Rights Reserved
SIMODRIVE 611 Configuration Manual (PJU) – 02/2012 Edition
NE module
Block diagram, 6-146
Interface overview, 6-147
Nominal load duty cycles, 6-169
Settings, 6-162
Network failure, 8-244
Method of operation, 8-307
No ground faults, 7-202
Nominal load duty cycles
FDD, 5-127
MSD-IM, 5-127
MSD-SRM, 5-127
Notes
Danger and warning information, viii
Hotline, vi
regarding the danger of electrostatic
discharge, xiv
Target group, vi
Technical, ix
Technical Support, vi
O
One-axis drive control, 4-83
Operation when the power fails, 8-307
Optional module
PROFIBUS-DP, 4-91
TERMINALS, 4-91
Ordering notes, 1-29
Overload protection, 8-306
Overview, 1-25
Overvoltage limiter module, 6-190, 7-203
Overvoltage limiting module, 6-141
P
Parallel operation, 8-302, 8-303
PC-Tools, 1-29
Personnel – Qualified?, vii
Position sensing, 2-49, 3-78
Direct, 3-68
Indirect, 3-68
Position sensing, direct, 3-68
Positioning, 3-68
Possible arrangements, 2-41
Power module, 5-121
Internal cooling, 2-52, 5-122
Technical specifications, 5-124
Power modules, 1-26
PROFIBUS DP
When can the modules be used?, 4-97
Which modules are available?, 4-96
PROFIBUS-DP, Which modules are available?,
4-91
Proper use, vii
Pulse enable, 8-246
D Index
D-481