NEC Express5800 Series Maintenance Manual page 204

Chapter 3 Appendix
Error
Class
code
UEFI 2404
UEFI 2405
UEFI 2406
UEFI 2407
UEFI 2408
UEFI 2409
UEFI 2410
UEFI 2411
UEFI 2412
UEFI 2413
UEFI 2414
UEFI 2415
UEFI 2416
UEFI 2419
UEFI 2420
UEFI 2421
UEFI 2422
UEFI 3100
204
Error message
Slot %1 SAN Error - Adapter restart failed.
Firmware not ready. Boot from SAN not
possible.
Slot %1 Error - Vital Product Data (VPD) is
not available.
Slot %1 NIC Error - NIC personality
(Ethernet, iSCSI, or FCoE) could not be
changed. FW may require update.
Slot %1 Error - The firmware update did not
complete successfully.
Slot %1 Error - Firmware image recovery
not successful.
Slot %1 Error - Failure to apply Virtual
Connect (VC) settings.
Slot %1 Error - Controller I/O timeout
failure.
%1: iSCSI Error - Failed to acquire DHCP
client network address.
%1: iSCSI Error - Failed to acquire DHCP
target network address.
%1: iSCSI Error - Failed to acquire DHCP
iSNS Server IP address.
%1: iSCSI Error - iSCSI login failed.
%1: iSCSI Error - Boot LUN not available.
%1: Error - Controller firmware not ready.
%1 %2 Error - Rx/Tx is disabled on this
device because an unsupported SFP+ or
QSFP module type was detected.
%1 %2 Error - The UEFI driver for the
device detected an older version of the
NVM image than expected.
%1 %2 Error - The UEFI driver for the
device detected a newer version of the
NVM image than expected.
%1 %2 Error - The UEFI driver for the
device stopped because the NVM image is
newer than expected.
Trusted Platform Module (TPM) was
successfully bound to system.
Express5800/R120h-1E, R120h-2E Maintenance Guide
Action
Reconnect SAN ports or restart the server. If the
problem persists, contact your sales representative.
Update the firmware of the card in slot %1. If the
problem persists, contact your sales representative.
Update the firmware of the NIC card in slot %1 before
restarting the server.
Update the firmware of the card again after confirming
the firmware image of the card in slot %1 is correct.
Restart the unit. If the problem persists, contact your
sales representative.
Confirm the VC configuration. Apply the VC
configuration again after restarting the server.
Restart the unit. If the problem persists, contact your
sales representative.
Check the network cables and the DHCP server
configuration. Restart the server.
Check the network cables and the DHCP server
configuration. Restart the server.
Check the network cables, the DHCP server
configuration and the iSNS server configuration. Restart
the server.
Confirm and set the cable connection, the controller
configuration, and the configurations of iSCSI initiator
and the target properly. Then restart the server.
Confirm and set the controller configuration and the
iSCSI server configuration properly. Then restart the
server.
Restart the unit. If the problem continues, update FW. If
the problem persists, contact your sales representative.
Contact your sales representative.
Update the NVM image. If the problem persists, contact
your sales representative.
Update the NVM UEFI driver to the latest version. If the
problem persists, contact your sales representative.
Update the NVM UEFI driver to the latest version. If the
problem persists, contact your sales representative.
Action is not necessary. The unit restarts automatically.
1. IML Error Message