Advertisement
N otice
e
CORRECTION
D
SERVICE FLASH
D
Please add this notice to the Manuals listed below.
Category : 8mm CAMCORDER
Model : RS MECHANISM
Destination : EUROPE, AUS., etc.,
@:
The reason of change.
Misprint
E : For Ease of Parts Procurements
Page 4-3.
[2] P re paration for Adj ustme nt (2)
[ O LD]
2-4.
Envelope Waveform Output Method
The envelope waveform can be output by connecting the
output terminals on the CP1
oscilloscope. To actually do this, connect a tape path
adjustment tool in between.
Connection method
(1 ) Clamp the clip of the tape path adjustment tool to
terminal J 1 005 of the CP1 circuit board so that the
positioning holes are aligned.
(2) Connect the terminals of the tape path adjustment
tool to an oscilloscope. The terminals to be connected
at this time are as follows.
A2 : Switching pulse (RF SW1 )
A3 : Envelope
A1 1 : Ground
2-5.
PCM Range Output Method
After the envelope waveform has been output according
to the method outlined in 2 - 4., if the two terminals
indicated below of the tape path adjustment tool are
shorted, the head output will be fixed at channel B and
an envelope waveform which includes the PCM range of
channel B will be output.
A4 . . . RF SW2
A1 1 . . . G N D
Sep./ '93/3,400 Ml Printed in Japan
D
PRODUCTION CHANGE
D
ADD I N FORMATION
D
REF : No. MM 550005
B : Quality Reliabilities
CN-A
A2 A4 A6 AS A l D
Al A3A5 A7 A9 A1 1
0 0 0 0 0
0 0 0 0 0 0
Pin layout on terminal board
circuit board to an
(PB RF)
(GN D)
SANYO ELECTRIC Co., Ltd.
Effective from : Serial NO.
C : Standardization
D : Design
F :
G :
CN-B
B2 B4 B6 BS B 1 0
Bl B3 B5 B7 B9 B 1 1
0 0 0 0 0
0 0 0 0 0 0
Tape path adjustment should be carried out with this
envelope waveform which includes the PCM range.
However, in other cases, the PCM region will not be
output.
2-6.
Setting the T est Mode
To set test mode, short the two terminals indicated below
of the tape path adjustment tool.
8 9
:
TEST
81 1 :
GND
2-7.
Setting the Shift T rack Mode
After setting the test mode by the method in 2-6., press
the ST ART/STOP button on the PW1 circuit board once
to set the shift track mode. When this mode is set, only
the fixed amount of track shift will occur, and the result of
this will be that the amplitude of the envelope waveform
will become 2/3 that of the previous waveform.
If the PLAY button on the CP1 circuit board is pressed or
if test mode is canceled during the shift track mode, the
shift track mode will be canceled.
(Furthermore, the START/STOP and PLAY buttons on
the remote control can also be used .)
See t h e reverse s i d e o f t h i s notice
REFERENCE No.
Date :
20 , 9, '93
Issue Number
3
V M - R Z 2 P
( U K )
1 2 6 - 0 3 5 - 0 4
V M - R Z 3 P
( S W )
1 2 6 - 0 2 6 - 0 3
1 2 6 - 0 2 6 - 0 0
( G )
1 2 6 - 0 2 6 - 0 5
( S P )
( I I )
1 2 6 - 0 2 6 - 0 5
( M E )
1 2 6 - 0 2 6 - 0 6
1 2 6 - 0 2 6 - 0 7
( U K )
1 2 6 - 0 2 6 - 0 8
( A U )
V M - E X 7 0 P ( G )
1 2 6 - 0 3 2 - 0 0
1 2 6 -,o 3 2 - 0 6
V M - E X 7 0 P ( A U )
V M - D 9 0 P
( U K )
1 2 6 - 0 3 5 - 0 5
V M - E X 2 0 P ( U K )
1 2 6 - 0 3 9 - 0 0
V M - E X 2 5 P ( U K )
1 2 6 - 0 3 9 - 0 1
V M - E X 3 0 P ( S P )
1 2 6 - 0 3 0 - 0 4
"
( A U )
1 2 6 - 0 3 0 - 0 8
( G )
1 2 6 - 0 3 0 - 0 0
( B L )
( M E )
1 2 6 - 0 3 0 - 0 5
1 2 6 - 0 3 0 - 0 6
V M - E X 7 0 P ( E X )
1 2 6 - 0 3 0 - 0 5
-+
M M 550005-03
Advertisement
