Motorola MSF 5000 Instruction Manual page 133

Chapter
2
Operation
MSF
5000
Instruction Manual
Special Service
Modes
Status
EEPOT
NUMBER
J
EEPOT VALUE (00 =
minimum
to
99
=
maximum)
MSFI045
011194JNM
Figure 2-3
Status Display
-
EEPOT
Adjustment
Mode
5.
Toselecta
different
EEPOT,
press and release the Select/Set switch to Select.
Verify
the decimal point shows on the Status display.
6.
Repeatedly
press the Select/Set switch
to
Select until the decimal
point
moves to the right of
the leftmost
digit.
NOME
If
more than 5 seconds pass between step
7
and step
8,
the select mode has timed-out and the decimal
point
disappears. To reactivate the select mode, press the
Select/Set switch
to Select.
If
the
Select/Set switch is
moved
to
Set
after the decimal
point disappears,
the
station exits the
EEPOT
adjust mode.
7.
Repeatedly press
the
Select/Set switch
to
Set until
the number
of
the
EEPOT
requiring adjustment appears in
the left position.
Table 2-3 lists the numbers of the EEPOTs.
NOME
If
the desired
EEPOT
number is passed
by, continue
toggling
the
Set switch until
the number appears
again. The EEPOTs
are accessed
sequentially.
8
Repeatedly
press the
Select/Set switch
to
Select until
the
decimal point
moves to the right of
the second
digit.
9.
Repeatedly press
the
Select/Set switch
to
Set until
the desired
EEPOT
coarse
level adjustment appears in
the
Status display.
10.
Repeatedly
press the Select/Set switch
to
Select until
the decimal point
moves to the right of the third digit.
2-14
68P81092E06
3/14/94
Chapter
2
Operation
MSF
5000
Instruction Manual
Special Service
Modes
Status
EEPOT
NUMBER
J
EEPOT VALUE (00 =
minimum
to
99
=
maximum)
MSFI045
011194JNM
Figure 2-3
Status Display
-
EEPOT
Adjustment
Mode
5.
Toselecta
different
EEPOT,
press and release the Select/Set switch to Select.
Verify
the decimal point shows on the Status display.
6.
Repeatedly
press the Select/Set switch
to
Select until the decimal
point
moves to the right of
the leftmost
digit.
NOME
If
more than 5 seconds pass between step
7
and step
8,
the select mode has timed-out and the decimal
point
disappears. To reactivate the select mode, press the
Select/Set switch
to Select.
If
the
Select/Set switch is
moved
to
Set
after the decimal
point disappears,
the
station exits the
EEPOT
adjust mode.
7.
Repeatedly press
the
Select/Set switch
to
Set until
the number
of
the
EEPOT
requiring adjustment appears in
the left position.
Table 2-3 lists the numbers of the EEPOTs.
NOME
If
the desired
EEPOT
number is passed
by, continue
toggling
the
Set switch until
the number appears
again. The EEPOTs
are accessed
sequentially.
8
Repeatedly
press the
Select/Set switch
to
Select until
the
decimal point
moves to the right of
the second
digit.
9.
Repeatedly press
the
Select/Set switch
to
Set until
the desired
EEPOT
coarse
level adjustment appears in
the
Status display.
10.
Repeatedly
press the Select/Set switch
to
Select until
the decimal point
moves to the right of the third digit.
2-14
68P81092E06
3/14/94