Motorola MSF 5000 Instruction Manual page 243

MSF
5000
Instruction Manual
Appendix
B
Error Codes
Digital Error Codes
Table B-3
Digital Error
Codes (Continued)
Error
Description
Probable Cause Corrective Action
dd2
Secure
MUXbus data strobe bad Data
strobe
signal (DS, U4014-47)
Replace
the standard mode
ASIC
on
(normal operating mode)
shorted.
the Secure board.
One of the
following MUXbus
Address lines (BAO-BA3,
U4014-42
thru U4014-45) shorted
to
ground.
DS
or
BAO-BA3 pin drivers
on
standard mode
ASIC
(U4014)
defective.
dd3 Secure
MUXbus
bad (internal The Secure standard mode
ASIC
is
Replace standard mode
ASIC
on the
loopback)
defective. Secure board.
dd4 Secure
MUXbus
bad (normal One of
the
following MUXbus
Replace standard mode
ASIC
on the
operating mode)
address lines
(BAO-BA3,
U4014-42 Secure board.
thru U4014-45) shorted high.
One of
the
following MUXbus
data lines
(BD0-BD3,
U4014-38
thru U4014-41) shorted to
ground.
BAO-BA3 or BDO-BD3 pin drivers
on Standard Mode
ASIC
defective.
dd5 Secure standard mode
ASIC
latch/
The Secure standard mode
ASIC
is
Replace standard mode
ASIC
on the
buffer bad (loopback) defective. Secure board.
dd7 Secure
HSR Clk/Sync
bad (internal The Secure standard mode
ASIC
is Replace standard mode
ASIC
on
the
loopback)
defective. Secure board.
dds Secure HSR Clk/Sync bad (normal The HSR Clock
or the
HSR
Sync
is
Check
for shorts on
HSR Clk
and
operating mode)
not operating properly.
HSR
Sync.
If
no shorts are
found, replace
standard mode
ASIC
on the Secure
board.
dd9 Secure
HSR
data
I/O
bad (internal The Secure standard mode
ASIC
is
Replace standard mode
ASIC
on the
defective. Secure board.
loopback)
ddA
Secure
HSR
data
I/O
bad (normal The
HSR out-to-HSR
in signal path is
Replace
the standard mode
ASIC
on
the Secure board.
operating mode)
open (not continuous). Secure
standard mode
ASIC
defective.
ddb The
Secure
ASIC
is defective. Bad transmit phase lock detector in
Replace
the
Secure
ASIC
on the
ASIC
Secure board.
ddC
The Secure
ASIC
is defective. Bad
RX
phase lock detector in
Secure
Replace
the Secure
ASIC
on the
ASIC
Secure board.
ddE Bad transmit P-S or S-P converter in The Secure
ASIC
is defective.
Replace
the Secure
ASIC
on the
Secure
ASIC
Secure board.
ddF Bad
RX
P-S or S-P converter in Secure The Secure
ASIC
is defective.
ASIC
Secure board.
Replace
the
Secure
ASIC
on
the
dEO
Non-zero user area check byte on
Center if
the error recurs.
Contact Motorola System Support Contact Motorola System Support
Center
if
the error recurs.
RAC/SAM
dE1
Non-zero
EEPROM
check byte on
Center if
the error recurs.
Contact Motorola System Support
Center if
the error recurs.
Contact Motorola System Support
RAC/SAM
dE2
Codeplug
on
RAC/SAM
nor
RAC/
SAM Center if
the error recurs.
Contact Motorola System Support
Center if
the error recurs.
Contact Motorola System Support
68P81092E09
3/14/94
B-21
MSF
5000
Instruction Manual
Appendix
B
Error Codes
Digital Error Codes
Table B-3
Digital Error
Codes (Continued)
Error
Description
Probable Cause Corrective Action
dd2
Secure
MUXbus data strobe bad Data
strobe
signal (DS, U4014-47)
Replace
the standard mode
ASIC
on
(normal operating mode)
shorted.
the Secure board.
One of the
following MUXbus
Address lines (BAO-BA3,
U4014-42
thru U4014-45) shorted
to
ground.
DS
or
BAO-BA3 pin drivers
on
standard mode
ASIC
(U4014)
defective.
dd3 Secure
MUXbus
bad (internal The Secure standard mode
ASIC
is
Replace standard mode
ASIC
on the
loopback)
defective. Secure board.
dd4 Secure
MUXbus
bad (normal One of
the
following MUXbus
Replace standard mode
ASIC
on the
operating mode)
address lines
(BAO-BA3,
U4014-42 Secure board.
thru U4014-45) shorted high.
One of
the
following MUXbus
data lines
(BD0-BD3,
U4014-38
thru U4014-41) shorted to
ground.
BAO-BA3 or BDO-BD3 pin drivers
on Standard Mode
ASIC
defective.
dd5 Secure standard mode
ASIC
latch/
The Secure standard mode
ASIC
is
Replace standard mode
ASIC
on the
buffer bad (loopback) defective. Secure board.
dd7 Secure
HSR Clk/Sync
bad (internal The Secure standard mode
ASIC
is Replace standard mode
ASIC
on
the
loopback)
defective. Secure board.
dds Secure HSR Clk/Sync bad (normal The HSR Clock
or the
HSR
Sync
is
Check
for shorts on
HSR Clk
and
operating mode)
not operating properly.
HSR
Sync.
If
no shorts are
found, replace
standard mode
ASIC
on the Secure
board.
dd9 Secure
HSR
data
I/O
bad (internal The Secure standard mode
ASIC
is
Replace standard mode
ASIC
on the
defective. Secure board.
loopback)
ddA
Secure
HSR
data
I/O
bad (normal The
HSR out-to-HSR
in signal path is
Replace
the standard mode
ASIC
on
the Secure board.
operating mode)
open (not continuous). Secure
standard mode
ASIC
defective.
ddb The
Secure
ASIC
is defective. Bad transmit phase lock detector in
Replace
the
Secure
ASIC
on the
ASIC
Secure board.
ddC
The Secure
ASIC
is defective. Bad
RX
phase lock detector in
Secure
Replace
the Secure
ASIC
on the
ASIC
Secure board.
ddE Bad transmit P-S or S-P converter in The Secure
ASIC
is defective.
Replace
the Secure
ASIC
on the
Secure
ASIC
Secure board.
ddF Bad
RX
P-S or S-P converter in Secure The Secure
ASIC
is defective.
ASIC
Secure board.
Replace
the
Secure
ASIC
on
the
dEO
Non-zero user area check byte on
Center if
the error recurs.
Contact Motorola System Support Contact Motorola System Support
Center
if
the error recurs.
RAC/SAM
dE1
Non-zero
EEPROM
check byte on
Center if
the error recurs.
Contact Motorola System Support
Center if
the error recurs.
Contact Motorola System Support
RAC/SAM
dE2
Codeplug
on
RAC/SAM
nor
RAC/
SAM Center if
the error recurs.
Contact Motorola System Support
Center if
the error recurs.
Contact Motorola System Support
68P81092E09
3/14/94
B-21