Checking The Hydrostatic Braking Distance - Toro Reelmaster 5510 Operator's Manual

Setting the Blade Count
1. In the Settings Menu, scroll down to Blade
Count.
2. Press the right button to change the blade count
between 8 or 11 blade reels.
Setting the Height of Cut (HOC)
1. In the Settings Menu, scroll down to HOC.
2. Press the right button to select HOC.
3. Use the center and right button to select the
appropriate HOC setting. (If the exact setting is
not displayed, select the nearest HOC setting
from the list displayed).
4. Press the left button to exit HOC and save the
setting.
Setting the Front and Rear Reel
Speeds
Although the front and rear reel speeds are calculated
by inputting the number of blades, mow speed and
HOC into the InfoCenter, the setting can be manually
changed to accommodate for different mowing
conditions.
1. To change the Reel Speed Settings, scroll down
to the F Reel RPM, R Reel RPM, or both.
2. Press the right button to change the reel speed
value. As you change the speed setting, the
display continues to show the calculated reel
speed based on blade count, mow speed and
HOC, which was previously entered, but the
new value is also displayed.
To Access Protected Display
Screens
From the main screen, press the center button once,
when the arrows appear above the buttons, press
the center button again to scroll through the display
screens.
Setting the Maximum Allowed
Mow Speed
The selected setting is displayed as an X on the
traction-speed bar graph along with the cruise control
and pedal stop settings. An X in a bar denotes that the
maximum speed is limited by the supervisor
47 or Figure 49).
Note:
This setting is retained in memory and applied
to the traction speed until you change it.
1. In the Settings Menu, scroll down to Mow Speed
and press the right button.
2. Use the right button to increase the maximum
mow speed in 0.8 km/h (0.5 mph) increments
between 1.6 and 12.9 km/h (1.0 and 8.0 mph).
3. Use the center button to decrease the maximum
mow speed in 0.8 km/h (0.5 mph) increments
between 1.6 and 12.9 km/h (1.0 and 8.0 mph).
4. Press the left button to exit.
Setting the Maximum Allowed
Transport Speed
The selected setting is displayed as an X on the
traction-speed bar graph along with the cruise control
and pedal stop settings. An X in a bar denotes that the
maximum speed is limited by the supervisor
47 or Figure
Note:
This setting is retained in memory and applied
to the traction speed until you change it.
1. In the Settings Menu, scroll down to Transport
Speed and press the right button.
2. Use the right button to increase the maximum
transport speed in 0.8 km/h (0.5 mph) increments
between 8.0 and 16.0 km/h (5.0 and 10.0 mph).
3. Use the center button to decrease the maximum
transport speed in 0.8 km/h (0.5 mph) increments
between 8.0 and 16.0 km/h (5.0 and 10.0 mph).
4. Press the left button to exit.
Turning the Smart Power ON/OFF
1. In the settings menu, scroll down to Smart
Power.
2. Press the right button to switch between O
O .
FF
3. Press the left button to exit.
Setting the Acceleration Mode
1. In the Settings Menu, scroll down to Acceleration.
2. Press the right button to switch between L
M
EDIUM
3. Press the left button to exit.
Checking the Hydrostatic
Braking Distance
(Figure
This machine will dynamically brake and stop when
you return the traction pedal to neutral.
Note:
For smooth deceleration, use your foot to
slowly control the traction pedal back to neutral. Do
not take your foot off the pedal and allow it to snap
29
49).
, and H .
IGH
(Figure
and
N
,
OW