Husqvarna DC 655 Operator's Manual page 8

when the product is started. This can
influence the operation of other products, for
example flicker on the lights.
• The power plug must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric
shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Make sure that the power, fuse and mains voltage
are the same as the voltage shown on the rating
plate of the product.
• Always stop the product before you disconnect the
power plug.
• Make sure that the ON/OFF switch is in OFF position
before the product is connected to the power supply.
• Always disconnect the power plug during a long
product stop.
• Do not use the product if the supply cord or power
plug is damaged. If the supply cord is damaged, it
must be replaced by the manufacturer, its service
agentor similarly qualified persons in order to avoid
a hazard. A damaged power cord can cause serious
injury and death.
• Use the power cord correctly. Do not use the power
cord to move, pull or disconnect the product. Pull the
power plug to disconnect the power cord. Do not pull
the power cord.
• Only operate the product on dry surfaces.
• Keep the product away from rain. Water that goes
into the product increases the risk of electrical shock.
• Always disconnect the power cord before you
connect or disconnect the connection for the motor
cable and the electrical enclosure.
• In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance
must not be supplied through an external switching
device, such as a timer, or connected to a circuit that
is regularly switched on and off by the utility.
Grounded product instructions
WARNING:
result in electrical shock. Speak to an
approved electrician if you are not sure if
your mains outlet is correctly grounded.
Do not do modifications to the power plug
from its factory specification. If the power
plug or power cord is damaged or must be
replaced, speak to your Husqvarna service
agent. Obey local regulations and laws.
If you do not fully understand the
instructions about the grounded product,
speak to an approved electrician.
8
Incorrect connection can
Use only grounded outdoor extension cables with
grounding plugs and grounding outlet that accepts the
product power plug.
The product has a grounded power cord and power
plug. Always connect the product to a grounded mains
outlet. This decreases the risk of electrical shock.
Do not use electrical adapters with the product.
Extension cables
• Use only approved extension cables with applicable
properties.
• The rated value on the extension cable must be the
same or higher than given on the rating plate of the
product.
• Use grounded extension cables.
• When you operate the product outdoors, use
an extension cable that is applicable for outdoor
operation. This decreases the risk of electrical
shock.
• Keep the connection to the extension cable dry and
off the ground.
• Keep the extension cable away from heat, oil, sharp
edges or moving parts. A damaged cable increases
the risk of electrical shock.
• Make sure that the extension cable is in good
condition and not damaged.
• Do not use the extension cable while it is wound up.
This can cause the extension cable to become too
hot.
• Make sure that the extension cable is out of the
way and the product during operation. This prevents
damage to the extension cable.
Safety devices on the product
WARNING:
instructions that follow before you use the
product.
• Do not use the product if the safety devices are
damaged or does not operate correctly.
• Do a check of the safety devices daily. If your safety
devices are damaged or does not operate correctly,
speak to your Husqvarna service agent.
• Do not make modifications on safety devices
Emergency stop button
The emergency stop button is used to quickly stop the
product and breaks the mains power supply.
To do a check of the emergency stop button
Refer to Control panel overview DC 975 on page 3 for
information about where the emergency stop button is
on your product.
1. Turn the emergency stop button clockwise to make
sure that the emergency stop button is disengaged.
Read the warning
2061 - 001 - 13.02.2023