NEC Express5800/R120g-1E Maintenance Manual page 190

Chapter 3 Appendix
Error Message
Cluster On Die was not ready. Cluster On Die feature is
A428
DIMM population is
A429 insufficient for Cluster On
Die.
Memory not detected
A800
PEI MEMORY NONE USEFUL
A801
Latest memory module is
A804
corrupted.
AE01 CPU1_DIMM1 has been
disabled.
AE02 CPU1_DIMM2 has been
disabled.
AE03 CPU1_DIMM3 has been
disabled.
AE04 CPU1_DIMM4 has been
disabled.
AE05 CPU1_DIMM5 has been
disabled.
AE06 CPU1_DIMM6 has been
disabled.
AE07 CPU1_DIMM7 has been
disabled.
AE08 CPU1_DIMM8 has been
disabled.
AE0D CPU2_DIMM1 has been
disabled.
AE0E CPU2_DIMM2 has been
disabled.
AE0F CPU2_DIMM3 has been
disabled.
AE10 CPU2_DIMM4 has been
disabled.
AE11 CPU2_DIMM5 has been
disabled.
AE12 CPU2_DIMM6 has been
disabled.
AE13 CPU2_DIMM7 has been
disabled.
AE14 CPU2_DIMM8 has been
disabled.
AE81 CPU1_DIMM1 with error is
enabled.
AE82 CPU1_DIMM2 with error is
enabled.
190
Cause
disabled in this hardware
configuration.
Cluster On Die feature cannot work
with this memory configuration.
No valid memory is installed.
No valid memory is installed.
Failure on BIOS Flash ROM was
detected.
A memory error was detected.
CPU1_DIMM1 has been disabled.
A memory error was detected.
CPU1_DIMM2 has been disabled.
A memory error was detected.
CPU1_DIMM3 has been disabled.
A memory error was detected.
CPU1_DIMM4 has been disabled.
A memory error was detected.
CPU1_DIMM5 has been disabled.
A memory error was detected.
CPU1_DIMM6 has been disabled.
A memory error was detected.
CPU1_DIMM7 has been disabled.
A memory error was detected.
CPU1_DIMM8 has been disabled.
A memory error was detected.
CPU2_DIMM1 has been disabled.
A memory error was detected.
CPU2_DIMM2 has been disabled.
A memory error was detected.
CPU2_DIMM3 has been disabled.
A memory error was detected.
CPU2_DIMM4 has been disabled.
A memory error was detected.
CPU2_DIMM5 has been disabled.
A memory error was detected.
CPU2_DIMM6 has been disabled.
A memory error was detected.
CPU2_DIMM7 has been disabled.
A memory error was detected.
CPU2_DIMM8 has been disabled.
An error in CPU1_DIMM1 was
detected, but because all memory
is currently disabled, this DIMM
was forcibly enabled.
An error in CPU1_DIMM2 was
detected, but because all memory
is currently disabled, this DIMM
was forcibly enabled.
Express5800/R120g-1E Maintenance Guide
1. POST Error Message
Solution
Replace the processor with the one that
supports this feature. Or, run SETUP and
select Disabled for the Cluster On Die. If the
same error persists, contact your sales
representative.
Check if memory configuration is correct. If
the same error persists, contact your sales
representative.
Check if DIMMs are properly installed. If the
same message appears repeatedly, contact
your sales representative.
Check if memory configuration is correct. If
the same error persists, contact your sales
representative.
Contact your sales representative.