Table of Contents
Advertisement
•
Make sure the machine can travel over all inequalities on the surface. Small inequalities for example
weld seams or floor joints are no barriers for the machine.
•
Never stay in the rain with the machine.
•
Do a check if there are any obstacles that can snag the cables when the machine moves.
•
Remove reinforcing steel or other objects protruding from the surface in order to prevent damage to
the machine.
•
Make sure that the surface does not contain dangerous materials, such as:
- combustible or explosive dusts or substances.
- carcinogenic or pathogenic substances.
•
Secure the work area around the machine in public areas. Keep an adequate safety distance from the
machine. Use a red and white safety chain and danger sign to enclose the work area.
•
If the proper execution of the work requires the presence of workers in the work zone, it is mandatory
to take effective measures to prevent them from serious injury.
•
It is forbidden to use/drive the machine on public roads, pavements, etc. unless they are closed for the
general public and other traffic.
•
Only work on locations which are adequately ventilated.
•
Do not use the product in areas where fire or explosions can occur. The product creates sparks and
flammable material can create ignition with the dust or fumes.
•
Make sure that only approved persons are in the work area.
•
Keep the work area clean and fully illuminated. Cluttered or dark areas invite accidents.
•
Remove objects such as screws, bolts, wires and stones from the work area before you use the product.
•
Make sure that there are no cables or hoses in the operation direction of the product.
•
Make sure that uneven surfaces, such as welded seams or floor joints, do not stop the product.
•
Make sure that there is sufficient airflow in the work area.
3.3
Electrical safety
•
Use only extension cables for extending the main cable that have size and marks in accordance with the
overall power consumption of the machine. Do not use damaged extension cables.
•
Make sure that the phases and the ground wire of the extension cable(s) are connected in the same
order as the supply cable of the machine and the power supply.
•
Electrical cables must be rolled entirely off of the reels.
•
Any damage to the electric cables and/or electrical components is not permitted.
•
If a cable or plug is damaged, it must be replaced immediately. Only use original Husqvarna parts.
•
The voltage on the identification plate must comply with the power supply.
•
Use an electrical power supply connection with ground connection and ground leakage circuit breaker.
•
The circuit breaker of the power supply must have a "D'' characteristic. Circuit breakers with "C" or "B"
characteristic can cause problems when the motor starts.
•
Keep the machine original. The machine is always equipped with a ground connection, do not change
this and always use ground cables with a ground plug.
•
Examine and test the electrical components regularly. The electrical components have to comply with
the requirements set out in the harmonised norm EN60204-1.
•
Always speak to a skilled electrician or your distributor when you have questions about the safety of the
electrical components.
•
Work on an electrical equipment or operating materials must be done only by a skilled electrician or by
trained persons with the guidance and supervision of a skilled electrician as well as in accordance with
the electrical engineering regulations.
•
Always use tools that are insulated against high voltages.
•
Do not abuse the cables. Never use the cables for carrying, pulling or unplugging the machine. Keep
cables away from heat, oil, sharp edges or moving parts. Damaged or entangled cables increase the
risk of electric shock and can cause serious injury and death.
•
Be careful with water on the treated surface. Electrical cables must not come into contact with water.
•
The main power switch on the machine must be in the "Off" position before you connect machine to the
power supply.
•
If the machine has a long standstill, pull out the main plug and cover it with plastic foil.
•
If the machine uses power from a generator, the generator must be operated in accordance with the
current legal regulations and directives in force (this applies to the protective ground conductor in
particular). In order to make sure that all safety devices work properly and to eliminate possible damage
to electrical components.
8
21.07.2023
Advertisement
Table of Contents
