Fujitsu MAX3073NC - SCSI,80, Dell DC961,Hard Drive Scsi Logical Interface Specifications page 305

command ..................................................3-102
parameter ...................................... 3-103, 3-104
sense command ..................................................3-1
sense data ...........................................................5-1
additional information ................................5-12
analysis and error recovery method............5-15
basic information ..........................................5-2
error classification ..........5-15, 5-16, 5-17, 5-18
error recovery methods.................................5-1
format ...........................................................5-1
hold condition.............................................1-22
hold state.....................................................1-22
in not ready state.........................................1-25
sense data hold state, other than .......................1-21
sense data length ..............................................3-36
sense key .................................................... 5-3, 5-5
inherent information .....................................5-4
specific valid.................................................5-4
sent PCOMP_EN .............................................4-41
SET DEVICE IDENTIFER
parameter list ..............................................3-70
SET DEVICE IDENTIFIER ............................3-69
SET LIMITS ....................................................3-78
command ....................................................3-79
setting parameter by MODE SELECT
command .........................................................6-6
single command .................................................1-8
SIZE .................................................................4-24
size enable ........................................................4-24
SKSV .................................................................5-4
SMART data page............................................4-72
SMART status page .........................................4-71
soft sectoring ....................................................4-16
soft write protect ..............................................4-30
spare sector area .................................................6-2
spare sector within cell.......................................6-2
specified cycle count over device lifetime .......4-65
specifying initialization method .......................3-83
specifying range where access is permitted .....3-79
SPF ................................................ 3-25, 3-37, 4-33
spindle motor start delay time ..........................3-18
SSEC ................................................................4-16
standard INQUIRY data............................. 3-3, 3-4
start specification .............................................3-42
START/STOP UNIT........................................3-41
starting boundary..............................................4-33
start-stop cycle counter ....................................4-65
page ............................................................4-63
status...................................................................1-6
stop format .......................................................3-85
stop specification..............................................3-42
STPF.................................................................3-85
sub page format...................................... 3-25, 3-37
subpage code ....................................................4-35
subpage length..................................................4-35
C141-C010
superseding reserve.......................................... 3-44
support ............................................................... 3-9
supported function ............................................. 3-6
supprot log page............................................... 4-49
SURF ............................................................... 4-17
surface addressing............................................ 4-17
SWP ................................................................. 4-30
SYNCHRONIZE CACHE ............................... 3-80
synchronous data transfer request.................... 3-17
synchronous mode data transfer....................... 1-15
synchronous transfer timeout........................... 4-34
T
tagged queuing................................................. 1-18
target certification list ...................................... 3-82
target save disable ............................................ 3-53
TASK SET FULL status .................................... 1-8
task set type...................................................... 4-28
TB ...................................................................... 4-3
temperature
page ............................................................ 4-62
termination status analysis and error
recovery method............................................ 5-12
TEST UNIT READY......................................... 3-1
threshold met criteria ....................................... 3-53
TMC................................................................. 3-53
total posted
read error .................................................... 4-56
recoverable verify error.............................. 4-60
verify error ................................................. 4-59
total posted recoverable read error................... 4-56
total posted recoverable write error ................. 4-53
total posted unrecoverable
verify error ................................................. 4-61
total posted unrecoverable read error............... 4-57
total posted unrecoverable write error ............. 4-54
total posted write error ..................................... 4-52
total read byte processed.................................. 4-57
total verify bytes processed.............................. 4-60
total write byte processed................................. 4-53
track count/zone............................................... 4-15
track skew factor .............................................. 4-16
transceiver mode .............................................. 4-41
transfer block ..................................................... 4-3
count............................................................. 1-4
transfer byte length .....................................1-4, 3-3
transfer data length............................................. 1-4
transfer period factor........................................ 4-40
transfer width exponent ................................... 4-40
TSD.................................................................. 3-53
TST .................................................................. 4-28
type of command and disconnect processing... 1-12
Index
IN-7