Table of Contents
Advertisement
planning
information
For 36"
gas model:
E36GC75GSS
Note:
For planning
purposes only. Refer
to Product Installation
Guide on the web at
electroluxicon.com for
detailed instructions.
Specifications subject
to change.
Optional
Accessories
Depth Adjustment
Filler Kit
PN # 903051-9010
9" Stainless
Steel Backsplash
PN # 903048-9010
Black Knobs Kit
PN # 903049-9120
34
cooktops
Gas and Electric Slide-In Cooktops
13"
max.
2"
cabinet
depth
Optional 9" stainless
steel backsplash
1" min. recommended
Side inset
distance between rear
edge of cutout and
nearest combustible
3"
surface above countertop
2" dia.
opening to route
power cable
22"
25" min.
1
/
"
1
8
max.
24"
Installation Specifications
•
Product Weight – 113 Lbs.
•
Voltage Rating – 120V / 1.2W / 60 Hz / 15 Amp
•
Connected Load (kW Rating) @ 120 Volts = 0.001 kW
(For use on adequately wired 120V, dedicated circuit
having 2-wire service with a separate ground wire.
Appliance must be grounded for safe operation.)
•
Amps @ 120 Volts = 0.008 Amps
•
Always consult local and national electric and gas codes.
•
Cooktop ships with 3/4" factory regulator.
•
LP Gas conversion kit supplied.
•
Respect critical dimensions as noted for proper
installation of cooktop.
•
When replacing an existing cooktop with countertop
cutout deeper than 7-1/4" and less than 8-1/2", order
free Depth Adjustment Filler Kit – (PN # 903051-9010).
•
Overhead cabinetry should not exceed a 13" max. depth.
•
Allow 30" minimum clearance between top of cooktop
and bottom of unprotected wood or metal overhead
cabinetry.
•
Absolute minimum horizontal distance between overhead
cabinets installed to either side of appliance must be
no less than maximum width of appliance.
36" min.
25
/
"
3
35
/
"
4
7
8
/
"
3
8
7
/
"
1
2
2"
2
/
"
1
2
35
3
/
16
*Both cutout dimensions are critical to proper cooktop
installation. Due to variations in countertop materials
4" x 4" opening to
it is recommended to undercut finished dimension
route gas supply
35-15/16" and adjust upon installation of cooktop.
•
Allow 24" minimum clearance when bottom of wood or
metal overhead cabinet is protected by not less than
1/8" flame-retardant millboard covered with not less than
No. 28 MGS sheet steel, 0.015" stainless steel, 0.024"
aluminum or 0.020" copper.
•
Allow 1" minimum clearance between rear edge of cutout
and nearest combustible surface above countertop.
•
Allow 7" minimum clearance from edge of cooktop to
nearest combustible wall on either side of unit.
•
Drawers not recommended beneath cooktop.
•
To reduce risk of fire when using overhead cabinetry,
install vent hood that projects horizontally a recommended
minimum of 7" beyond bottom of cabinets.
Combination Installations
For installation details refer to Project Planning Section.
•
Cooktop model E36GC75GSS is NOT approved to be
used over any Electrolux ICON
•
Cooktop model E36GC75GSS (without optional
backsplash) is approved to be used in combina tion
with an Electrolux ICON
Slide-In Cooktop /Downdraft Vent Countertop Preparation
page for installation specifications.) Proper combination
installation will require cooktop power cord to be relocated
to underside of unit. (For details, refer to 30" & 36" Gas
Slide-In Cooktop Power Cord Relocation Instructions
page or on the web at electroluxicon.com.)
30" min. for
unprotected cabinet
24" min. for
protected surface
18"
min.
7
/
"
3
4
7" min. to nearest
combustible wall
(either side of unit)
/
"
3
8
"
* 35
/
"
3
16
* 35
/
"
15
16
®
Single Wall Oven.
®
36" Downdraft Vent. (Refer to
7
/
"
1
4
Hide quick links:
Advertisement
Table of Contents
