Siemens SINUMERIK 840D sl Programming Manual page 419
Measuring cycles hmi sl
Hide thumbs
Also See for SINUMERIK 840D sl:
- Function manual (2184 pages) ,
- Programming manual (1334 pages) ,
- Commissioning manual (1102 pages)
Table of Contents
Advertisement
GUD up to Version 7.5
E_MESS_MS_IN
E_MESS_MT_IN
E_MESS_D
E_MESS_D_M
E_MESS_D_L
E_MESS_D_R
E_MESS_FM
E_MESS_F
E_MESS_FZ
E_MESS_CAL_D[3]
E_MESS_CAL_L[3]
E_MESS_MT_TYP[3]
E_MESS_MT_AX[3]
E_MESS_MT_DL[3]
E_MESS_MT_DR[3]
E_MESS_MT_DZ[3]
E_MESS_MT_DIR[3]
E_MESS_MT_D
E_MESS_MT_FM
E_MESS_MT_CF
E_MESS_MT_COMP
E_MESS_SETT[0]
E_MESS_SETT[1]
E_MESS_MS_SOUTH
E_MESS_MS_MONO
_MC_SIMSIM
_MC_SIMDIFF
See also
General information (Page 91)
Overview of the auxiliary programs required (Page 261)
General information (Page 378)
Overview of measuring cycle parameters (Page 421)
Measuring cycles
Programming Manual, 03/2009 Edition, 6FC5398-4BP10-2BA0
A.2 GUD variables that can no longer be used
MD/SD as of Version 2.6
MD51606 $MNS_MEA_INPUT_PIECE_PROBE[0]
MD51607 $MNS_MEA_INPUT_TOOL_PROBE[0]
MD51750 $MNS_J_MEA_M_DIST
MD51751 $MNS_J_MEA_M_DIST_MANUELL
MD51752 $MNS_J_MEA_M_DIST_TOOL_LENGTH
MD51753 $MNS_J_MEA_M_DIST_TOOL_RADIUS
MD51755 $MNS_J_MEA_MEASURING_FEED
MD51757 $MNS_J_MEA_COLL_MONIT_FEED
MD51758 $MNS_J_MEA_COLL_MONIT_POS_FEED
MD51770 $MNS_J_MEA_CAL_RING_DIAM
MD51772 $MNS_J_MEA_CAL_HEIGHT_FEEDAX
MD51774 $MNS_J_MEA_T_PROBE_TYPE
MD51776 $MNS_J_MEA_T_PROBE_ALLOW_AX_DIR
MD51778 $MNS_J_MEA_T_PROBE_DIAM_LENGTH
MD51780 $MNS_J_MEA_T_PROBE_DIAM_RAD
MD51782 $MNS_J_MEA_T_PROBE_T_EDGE_DIST
MD51784 $MNS_J_MEA_T_PROBE_T_EDGE_DIST
MD51786 $MNS_J_MEA_T_PROBE_MEASURE_DIST
MD51787 $MNS_J_MEA_T_PROBE_MEASURE_FEED
SD54690 $SNS_MEA_T_PROBE_MANUFACTURER
SD54691 $SNS_MEA_T_PROBE_OFFSET
SD55770 $SCS_J_MEA_SET_COUPL_SP_COORD
SD55771 $SCS_J_MEA_SET_CAL_MODE
MD51614 $MNS_MEA_PROBE_LENGTH_RELATE
SD55772 $SCS_J_MEA_SET_CAL_MODE
SD55618 $SCS_MEA_SIM_ENABLE
SD55619 $SCS_MEA_SIM_MEASURE_DIFF
Appendix
419
Advertisement
Table of Contents
