Toshiba H9 ASD Installation And Operation Manual page 285

RX2 (AI1) Input Bias, 163
RX2 (AI1) Input Gain, 163
RX2 (AI1) Input Point 1 Frequency, 117
RX2 (AI1) Input Point 1 Rate, 118
RX2 (AI1) Input Point 1 Setting, 116
RX2 (AI1) Input Point 2 Frequency, 117
RX2 (AI1) Input Point 2 Rate, 119
RX2 (AI1) Input Point 2 Setting, 117
S
S/L2, 16
S1, 21, 22
S2, 21, 22
S3, 21, 22
S4, 21, 22
Save User Settings, 75
Second Speed Loop Proportional Gain, 160
Second Speed Loop Stabilization Coefficient, 161
Send Wait Time (2-wire), 203
Setpoints, 59
Short Circuit Detection At Start, 185
Short Circuit Protection, 268
Simple Positioning Completion Range, 151
Sink, 24
Sink/Source Setting Error, 248, 249
Slip Frequency Gain, 151
Source, 24
SOUT, 252
S-Pattern 1, 165
S-Pattern 2, 165
S-Pattern Acceleration Lower-Limit Adjustment, 168
S-Pattern Acceleration Upper-Limit Adjustment, 168
S-Pattern Deceleration Lower-Limit Adjustment, 168
S-Pattern Deceleration Upper-Limit Adjustment, 168
Special, 56
Special Parameters, 57
Special Protection Parameters, 53
Speed 1 Operation Time, 177
Speed 10 Operation Time, 178
Speed 11 Operation Time, 178
Speed 12 Operation Time, 178
Speed 13 Operation Time, 179
Speed 14 Operation Time, 179
Speed 15 Operation Time, 179
Speed 2 Operation Time, 177
Speed 3 Operation Time, 177
Speed 4 Operation Time, 177
Speed 5 Operation Time, 177
Speed 6 Operation Time, 177
Speed 7 Operation Time, 178
Speed 8 Operation Time, 178
Speed 9 Operation Time, 178
278
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.ctiautomation.net - Email: info@ctiautomation.net
Speed at 0% Drooping Gain, 139
Speed at F320 Drooping Gain, 139
Speed Error, 248
Speed Limit (torque=0) Band, 157
Speed Limit (torque=0) Center Value, 156
Speed Limit (torque=0) Center Value Reference, 156
Speed Loop Proportional Gain, 160
Speed Loop Stabilization Coefficient, 160
Speed PID Switching Frequency, 161
Speed Reach Detection Band, 86
Speed Reach Frequency, 86
Speed Reference Setpoints, 55, 56
ST, 21, 22
Stall, 53
Stall Prevention During Regeneration, 160
Stall Prevention Factor 1, 154
Stall Prevention Level, 182
Standard Mode Selection, 46
Start Frequency, 123
Startup and Test, 27
Startup Wizard Parameter Requirements, 71
Stepout Current Detection Level, 190
Stepout Current Detection Time, 190
Stop-Reset Key, 31
SU+, 21, 23
Supply Voltage Correction, 137
Switching Load Torque During Power Running, 142
Switching Load Torque During Regenerative
Braking, 142
Synchronized Acceleration Time, 139
Synchronized Deceleration Time, 138
System Configuration and Menu Options, 41
System Grounding, 18
System Integration Precautions, 7
System Operation, 70
T
T/L3, 16
Tension Torque Bias Input, 154
Terminal, 47
Terminal Board, 21, 24
Terminal Descriptions, 22
Time Limit For Lower-Limit Frequency Operation, 125
Torque, 44, 59
Torque Bias Input Selection, 143
Torque Command Selection, 154
Torque Control, 59, 60
Torque Current, 44
Torque Limit Settings, 60
Torque Reference, 44
Torque Speed Limiting, 60
Trace, 49, 50
H9 ASD Installation and Operation Manual