Panasonic AK-HRP200G Operating Instructions Manual page 25

Parts and their functions (when operating a remote camera)
38. Character/Menu button <CHARA/MENU>
Press and hold this button (for about 2 seconds) to turn the on or off
the camera menu.
Press and hold (On): Turns on (displays) the camera menu.
Press and hold (off): Turns off the camera menu.
39.
Select dial <SELECT>
Use this dial to perform menu operations when the camera menu is
displayed.
For details on the camera menu, refer to the operating instructions for
the camera.
Increases the selected value or selects in the down
Turn clockwise:
direction of the menu.
Turn Decreases the selected value or selects in the up
counterclockwise: direction of the menu.
Confirms the selected value or confirms the
Press:
selected menu.
<Note>
When no menu is displayed, the select dial serves as the FOCUS/
ZOOM adjustment dial in the ZOOM/FOCUS setting mode. (→page 23)
40.
Red/green tally display, Call button <TALLY/CALL>
The tally lights red when the tally signal connected to the preview
connector <PREVIEW> of the unit is on.
The call button cannot be used during remote camera operation.
On (red): The tally of the camera being operated is on.
Off: The tally of the camera being operated is off.
41.
Alarm display <ALM>
This display indicates alarms.
Consult your supplier if a failure occurs.
An alarm (a cooling fan alarm) has been received from a
On:
remote camera.
Flashing: Indicates that the power voltage of the unit has decreased.
Off: Normal operating state
42.
Optical alarm display <OPT>
This is disabled for a remote camera.
39 38 40 43
CHARA
IRIS/M.PED LOCK
MENU
TALLY/CALL
52 ALM OPT
SENSE
EXT
SELECT
55
D.EXT
53
AUTO COARSE
54
CLOSE OPEN
CLOSE FULL
48 49 47 51
43.
44.
45.
46.
(continued)
IRIS M.PED
PUSH
41
PREVIEW
42
50
46
45
44
Iris/master pedestal lock button
<IRIS/M.PED LOCK>
Use this button to disable (lock) iris and M.PED operation.
The button lights red when operation is disabled. Press the button
again to release the lock.
Off: Iris and M.PED can be controlled.
Lit red: Operation is disabled (locked).
Indicates that the Iris lever was operated when operation
was disabled (locked).
Flashes red:
When the Iris lever is returned to the lock position, the
(Quick
button turns off and normal control becomes possible.
flashing
This also flashes if the camera adjustment values and iris
rate of
lever position are offset when the control target camera is
once every
switched. At the point in time when the iris lever is moved
second)
to the position that matches the camera adjustment values,
the button turns off and normal control becomes possible.
Indicates that the master pedestal control <M.PED> was
operated when the function was disabled (locked).
When the master pedestal control <M.PED> is returned to
Flashes red:
the lock position, the button turns off and normal control
(Slow
becomes possible.
flashing
This also flashes if the camera adjustment values and
rate of once
master pedestal control <M.PED> position are offset when
every 2
the control target camera is switched. At the point in time
seconds)
when the master pedestal control <M.PED> is moved to
the position that matches the camera adjustment values,
the button turns off and normal control becomes possible.
Iris lever <IRIS ( )>
Use this lever to adjust the iris level.
This lever is enabled when the iris/master pedestal lock is off.
If the auto iris is not on, the iris can be adjusted manually.
When manual iris adjustment (when the <IRIS/M.PED LOCK> and
<AUTO> buttons are all off)
Forward: Adjusts the iris in the CLOSE direction.
Backward: Adjusts the iris in the OPEN direction.
When auto iris is enabled (when the auto iris button <AUTO> is on),
use this lever to adjust the convergence level of the auto iris of the
remote camera.
Master pedestal control <M.PED>
Use this control to adjust the master pedestal level. Turn it clockwise
to increase the master pedestal.
Turning the master pedestal control <M.PED> displays the setting on
the setting display for about 2 seconds.
The master pedestal and the R, G, and B pedestal can be adjusted
independently. A master pedestal adjustment does not affect the R,
G, and B pedestal values.
Pressing the M.GAIN/M.PED DISPLAY SELECT button <M.GAIN/M.
PED> twice displays the setting on the setting display.
<Note>
This cannot be used with the AW-HE2.
Preview button <PREVIEW>
Outputs the preview signal from the preview connector. (→page 34)
On (press): Preview output ON
Off: Preview output OFF
25