Page 1
HUAWEI Airbridge BTS3606&3606A CDMA Base Station Installation Manual – BTS3606A Cabinet Installation V200R001 Huawei Technologies Proprietary...
Page 2
T2-030463-20050202-C-2.11 V200R001 Product Version 31041463 Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. Please feel free to contact our local office or company headquarters. Huawei Technologies Co., Ltd. Address: Administration Building, Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, P. R. China...
Page 4
This manual applies to Airbridge BTS3606A CDMA Base Station V200R001. Related Manuals The related manuals are listed in the following table. Manual Content Airbridge BTS3606&3606A Covers the system description, system CDMA Base Station Technical architecture and principles, interface protocols, Manual and services flows of the BTS3606/BTS3606A.
Page 5
Terminal Display is in Courier New. Courier New II. Command conventions Convention Description Boldface The keywords of a command line are in Boldface. Command arguments are in italic. italic Items (keywords or arguments) in square brackets [ ] are optional. Huawei Technologies Proprietary...
Page 6
<Enter>, <Tab>, <Backspace>, or <A>. Press the keys concurrently. For example, <Ctrl+Alt+A> <Key1+Key2> means the three keys should be pressed concurrently. Press the keys in turn. For example, <Alt, A> means the <Key1, Key2> two keys should be pressed in turn. Huawei Technologies Proprietary...
Page 7
Note, Comment, Tip, Knowhow, Thought: Means a complementary description. Environmental Protection This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed. Huawei Technologies Proprietary...
Page 10
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Table of Contents Chapter 5 Installing Cables ......................5-1 5.1 Types of Cables and Related Concepts ................5-1 5.1.1 Types of Cables for BTS3606A Deployment ............5-1 5.1.2 Related Concepts....................5-3 5.2 Cabling Diagram ........................
Page 11
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Table of Contents Index ..............................i-1 Huawei Technologies Proprietary...
Page 12
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station List of Figures List of Figures Figure 1-1 Dimensions of cement base of BTS3606A single cabinet (unit: mm) ....1-4 Figure 1-2 Dimensions of cement base of BTS3606A cabinet and auxiliary battery cabinet (unit: mm) ..........................
Page 13
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station List of Figures Figure 3-11 Mounting rodent-resistant plate ................ 3-10 Figure 3-12 Installing a board (1)..................3-13 Figure 3-13 Installing a board (2)..................3-14 Figure 3-14 Installing a board (3)..................3-14 Figure 3-15 Unlocking the rear door ..................
Page 14
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station List of Figures Figure 5-3 Inlet/outlet of RF cables..................5-8 Figure 5-4 Inlet/outlet panel after turnover................5-8 Figure 5-5 Installing RF cables ....................5-9 Figure 5-6 O(1) configuration....................5-11 Figure 5-7 O(2) configuration....................
Page 15
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station List of Figures Figure 5-37 Installing GPS lightning arrester (2) ..............5-35 Figure 5-38 Wrong and correct operations ................5-37 Figure 5-39 Making lugs ...................... 5-38 Figure 5-40 Removing the cover of the power lightning protection filter ......5-39 Figure 5-41 Installing the L1, L2, L3, and N lines ..............
Page 16
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station List of Tables List of Tables Table 1-1 Technical documents....................1-1 Table 1-2 Tools and instruments .................... 1-2 Table 4-1 Specifications of the TSI-DDF/ODF transmission interface box ......4-2 Table 4-2 Specifications of the PSI power interface box............
The customers must provide a copy of cable connections the documents to Huawei prior to the equipment delivery. The report is filled in by Huawei survey Site survey report engineers during site survey. Installation The document is prepared by Huawei...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 1 Installation Preparations 1.2 Tools and Instruments Table 1-2 lists the tools and instruments needed for the installation. Table 1-2 Tools and instruments Measuring Long tape, 50 m ribbon tape, 5 m measuring tape,...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 1 Installation Preparations Note: The equipment supplier provides the tool list and consults to the customer to specify the tool provider. The wire punchdown tool is delivered along with the cabinet.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 1 Installation Preparations heavy snow, the snow will not cover the lowest air inlet on the cabinet. It is suggested that the depth of the cement base be larger than 100 mm.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 1 Installation Preparations 1.3.3 Space Requirements For specific requirements on installation space, see Chapter 2 "Installing Cabinet Base or Channel Steel". 1.3.4 Power Supply and Grounding Requirements For the BTS3606A, power supply must meet the following requirements:...
The packing case is in good condition. The cabinet is placed upside down. If the outer package is damaged or soaked; or the equipment is soaked and becomes rusty, stop unpacking and find the cause. Feed back the situation to the local Huawei Representative Office. Note:...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 1 Installation Preparations Caution: When transporting and moving equipment, components, or parts, avoid them from colliding with doors, walls or shelves. Never touch the uncoated surface of equipment, parts, or components with sweat soaked or dirty gloves.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 1 Installation Preparations Woodenboard Steeledge Tongue Spanner Figure 1-3 Straightening the tongues After straightening all the tongues on the cover, remove the cover, as shown in Figure 1-4.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 1 Installation Preparations Straighten all the tongues that join the wooden boards around the wooden case and remove the wooden boards, as shown in Figure 1-5. Figure 1-5 Removing all left wooden boards Unpack other cases in the same way.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 1 Installation Preparations Otherwise, moisture will condense on the surface of the equipment, causing damage to To open a carton, proceed as follows: Check the types and quantity of boards inside the carton according to labels.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 2 Installing Cabinet Base or Channel Steel Chapter 2 Installing Cabinet Base or Channel Steel The BTS3606A is outdoor equipment. When it weights more than 800 kg, it must be installed on a cabinet base.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 2 Installing Cabinet Base or Channel Steel 88 mm 916 mm (36.063 inches) (3.465 inches) 73 mm 822 mm (32.362 inches) 856 mm (33.701 inches) (2.874 inches) 362 mm (14.252 inches)
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 2 Installing Cabinet Base or Channel Steel Start Lay out the installation position Does the cabinet weight less than 800 kg? Cast two cement Cast a cement plinth...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 2 Installing Cabinet Base or Channel Steel I. When There Is Only One BTS3606A Cabinet When there is only one BTS3606A cabinet, install it according to Figure 2-4 to facilitate the installation and maintenance.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 2 Installing Cabinet Base or Channel Steel 400mm (16in) 600mm (24in) 800mm (32in) (1) Battery cabinet (2) Front of battery cabinet (3) BTS3606A cabinet (4) Wall or other reference objects Figure 2-5 Installation position for a battery cabinet 2.3.2 Casting Cement Plinth...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 2 Installing Cabinet Base or Channel Steel Figure 2-6 Dimensions of a cement plinth II. Casting Cement Plinth When a Battery Cabinet Is Configured During the installation of the BTS3606A cabinet, the cement plinth is cast according to the outline and dimensions shown in Figure 2-7.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 2 Installing Cabinet Base or Channel Steel (1) Cement plinth (2) Outline of the cabinet (3) Installation hole of the expansion bolt (4) Front of the cabinet Figure 2-8 Layout and dimensions of installation holes for a BTS3606A cabinet Figure 2-9 illustrates the installation holes of expansion bolts when a battery cabinet is configured.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 2 Installing Cabinet Base or Channel Steel (1) Cement plinth (2) Outline of the battery cabinet (3) Installation hole of the expansion bolt (4) Position of the BTS3606A cabinet...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 2 Installing Cabinet Base or Channel Steel Use the M12 expansion bolt and φ16 bit. Hold the drill stock firmly with two hands, and keep the drill bit vertical to the ground to drill a hole.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 2 Installing Cabinet Base or Channel Steel 2.3.5 Fastening the Base To fasten the base, proceed as follows: Disassemble the cabling rack, rodent-resistant plate and anti-slip plate. Put the base on the cement plinth.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 2 Installing Cabinet Base or Channel Steel 2.4.1 Laying out Installation Position For details, see section 2.3.1 "Laying Out Installation Position". 2.4.2 Casting Cement Plinths Determine the position of the wall or beam that bears the BTS3606A. Then cast two cement plinths on the floor or platform right above the bearing wall or the beam.
Page 39
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 2 Installing Cabinet Base or Channel Steel Cast the channel steel and the cement plinths together with cement. Fasten the channel steel on the cement plinths with expansion bolts.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment Chapter 3 Installing Cabinet and Cabinet Equipment This chapter introduces how to install the BTS3606A cabinet, the battery cabinet, and the equipment inside these cabinets.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment (1) Lug (2) Mount angle Figure 3-1 Cabinet bearing points 3.1.2 Leveling Cabinet To level the cabinet, proceed as follows: Use a level bar to check the levelness of the cabinet in both the latitudinal and longitudinal directions.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment 3.1.3 Fastening Cabinet Note: Do not open the front door unless it is ensured that the cabinet is level. If the front door keeps open for a long time, use a solid object to support the lower part of the door to prevent the deformation of the door.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment Note: The front door can be fully opened to 120 The support bar can be fixed at an angle of 90 or 120 Fix one end of the bar on the rail with a fixing bolt as shown in Figure 3-5.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment (1) Base (2) Cabinet (3) M12 x 100 bolt (4) Spring washer 12 (5) Plain washer Figure 3-6 Installing the burglary-resisting bolt Note: Step 6 applies to the installation of BTS3606A cabinet on a base only.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment (1) Base (2) M8x20 screw (3) Cabling rack Figure 3-7 Mounting cabling rack On the rodent-resistant plate, cut an opening where the cable is led out or led in according to the shape of cables.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment (1) Base (2) Rodent-resistant plate (3) M6 x 12 screw (4) Lug Figure 3-8 Mounting the rodent-resistant plate 3.1.5 Removing Lugs (Optional) After the cabinet is installed, remove the lugs.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment (1) Base (2) M8x20 screw (3) Cabling rack Figure 3-10 Mounting the cabling rack Figure 3-11 shows how to mount the rodent-resistant plate.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment 3.2.5 Removing Lugs After the cabinet is installed, remove the lugs. Use the filler blocks delivered with the equipment to fill the holes on the lugs and then keep the lugs in the tool box.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment Caution: Disconnect all the cables on the rear door before removing the rear door. To remove the rear door of the BTS3606A, proceed as follows: Use the dedicated spanner attached to the BTS3606A cabinet to remove the M6 screws on the rear door.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment Wear an antistatic wrist strap and ground it by inserting its grounding plug to the antistatic jack on the side door post of the cabinet.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment Figure 3-13 Installing a board (2) Tighten the screws clockwise on the front panel. See Figure 3-14. Figure 3-14 Installing a board (3) 3.4.2 Installing Modules in RF Subrack...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment Check the cleanness of the subrack and clean it up. Wear the antistatic wrist strap. Align the RF module with the relevant subrack.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment 3.4.4 Installing Built-in Batteries The built-in batteries are installed after the batteries are connected with each other. For installation method, see section 5.10, “Installing Built-in Batteries".
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment To open the front door, proceed as follows: Unlock the door with the key. Pull the handle outwards to open the door.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment 3.6 Installation of Batteries in Auxiliary Battery Cabinet Caution: Arrange the batteries according to the positive and negative terminals as shown in Figure 3-16.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment (1) Baffle plate Figure 3-17 Removing baffle plates Put the batteries into the cabinet. Be sure that the side of the battery with connecting terminals must face outward.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 3 Installing Cabinet and Cabinet Equipment Figure 3-18 BTS3606A cabinet installed on cement plinth Figure 3-19 illustrates the auxiliary battery cabinet after it is installed on the cement plinth.
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes Chapter 4 Installing Outdoor Transmission and Power Interface Boxes This chapter introduces the functional structure of the outdoor transmission and power interface boxes and their installation procedures.
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes (1) Enclosure (2) Mains air breaker (3) Diesel air breaker (4) Air breaker interlock device (5) Input/output terminal bar Figure 4-3 Internal structure of PSI power interface box Table 4-2 lists the specifications of the power interface box.
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes Figure 4-4 Default configuration of PSI power interface box 4.2 Installing Outdoor Transmission and Power Interface Box Caution: When installing the transmission interface box, the length of the cable between the box and BTS3606A cabinet must be less than 7 m (240 in.).
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes Figure 4-5 Installation holes of expansion bolts Drill holes and install expansion bolts by following the instruction in section 2.3.4 “Drilling Holes and Installing Expansion Bolts”.
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes Adjust the location of the box. Tighten the nuts to 13.4 N m (116 in. lbs). 4.2.2 Mounting Transmission Interface Box on the Steel Pole Caution: The outer diameter of the steel pole must range from 60 mm (2.4 in.) to 114 mm (4.5...
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes (1) Steel pole (2) Beam (3) M10 nut (4) Plain washer 10 (5) Spring washer 10 (6) Long M10 bolt Figure 4-8 Mounting transmission interface box on the steel pole Install the plain washer, spring washer, and nut on the long bolt.
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes 4.3.1 Using 120Ω DDF Unit To use the 120Ω DDF unit, proceed as follows: Route cables to corresponding cable bands through the cabling holes on both sides of the 120Ω...
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes Figure 4-10 Cabling diagram after 120Ω DDF unit is installed (b) 4.3.2 Using 75Ω DDF Unit Connect cables according to the actual requirements. Figure 4-11 illustrates the cabling diagram after the installation of the 75Ω...
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes Figure 4-12 Grounding busbar To install the grounding busbar, proceed as follows: Loosen the fastening screw on the two ends.
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes To use the 12-core fiber fusing and distributing assemblies, proceed as follows: Lead the optical fiber through the waterproof locknut at the cable inlet and then into the enclosure.
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes 4.4 Installing Outdoor Power Input Components This section explains how to install: Diesel air breaker assemblies Grounding cable for enclosure...
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes (1) Support (2) Gliding block (3) Screw (4) Nut Figure 4-16 Mounting air breaker interlock device Loosen locknuts. Move the sliding block right and left, and adjust one air breaker until it is closed.
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes (1) Grounding nut Figure 4-18 Installing grounding cable for enclosure 4.4.3 Installing Input Components of Single-phase Mains and Diesel Caution: Make sure that the connection of neutral line (N) and live line (L) are correct.
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes (1) Mains input air breaker (2) Connecting busbar (3) Mains input (4) Power output Figure 4-20 Input of single-phase mains Connect the neutral line for mains input to terminal N1, and the live line to terminal L1, as shown in Figure 4-20.
Installation Manual – BTS3606A Cabinet Installation Chapter 4 Installing Outdoor Transmission and Airbridge BTS3606&3606A CDMA Base Station Power Interface Boxes Lead phase-A, phase-B, and phase-C wires in the corresponding output terminals among A, B, and C respectively, as shown in Figure 4-22.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Chapter 5 Installing Cables This chapter introduces the cables used for deployment of the BTS3606A and their installation procedures. 5.1 Types of Cables and Related Concepts This section introduces the cables used for BTS3606A deployment, and concepts of cable inlet and cable distribution region, and then provides cabling diagrams.
Page 80
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Type of cable Description Color Specification Single-mode optical fiber, 2 x Φ2 mm (0.08 in.) Optical fiber connecting ODU3601C Orange externally Φ4 mm (0.16 in.) (The...
This manual does not describe cables in the cabinet backplane as they are connected before delivery. For installation procedure of the feeder, see Airbridge BTS3606&3606A CDMA Base Station Installation Manual – Antenna & Feeder Installation. The specifications of the feeder and the jumper between the cabinet cable inlet and the feeder depend on the antenna configured.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables I. Cable Inlet Cable inlet is the entrance where the cables are led into the cabinet. All external cables of the BTS3606A are led into the cabinet from the inlets on the front part at the bottom of the cabinet.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Cable No. Cable name +27 V power input cable of CRFM5 Power input cable of baseband fan box Power input cable of the baseband subrack...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables RF jumper to feeder RF cables between CDDU/CHPA/CTRM (single-channel) RF cables between CDDU/CMPA/CMTR (multi-channel) 5.3.1 Connecting RF Jumper to Feeder If the BTS3606A operates in diversity receiving mode using two antennas, the...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Coat the silicon gel on the connector for waterproof treatment, as shown in Figure 5-5. (1) Wiping the silicon gel Figure 5-5 Installing RF cables Place the inlet panel back to its original position after installation.
Page 88
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Typical Quantity Quantity Diversity LNA Quantity of configuration of CDDU of CHPA status in CTRM CPCM Normal O(1) power synthesis amplification S(1/1/1) power Normal synthesis...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Sector C Sector B Sector A CDDU CTRM CHPA PAout PAin Figure 5-6 O(1) configuration II. O(2) Configuration The O(2) refers to an omni cell with two carriers.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables IV. S(2/2/2) Configuration The S(2/2/2) refers to three sectors, each configured with two carriers. Figure 5-9 shows RF cable connections, indicated by the blue lines.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Sector A Sector B Sector C CDDU CHPA CPCM PAout PAin CHPA CTRM PAout PAin Figure 5-10 O(1) power synthesis VI. S(1/1/1) Power Synthesis Figure 5-11 illustrates the connections of RF cables for the power synthesis in the case of S(1/1/1) configuration.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Sector Sector Sector CDDU CMTR CMPA RF_out RF_in Sample Figure 5-12 O(1) configuration II. O(2) Configuration The O(2) refers to an omni cell with two carriers. Figure 5-13 shows RF cable connections, indicated by blue lines.
Page 95
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables III. S(1/1/1), Low-Power S(2/2/2), and Low-Power S(3/3/3) Configurations Figure 5-14 shows RF cable connections for the S(1/1/1) configuration, indicated by blue lines. RF cable connections for the low-power S(2/2/2) configuration and low-power S(3/3/3) are the same as that for S(1/1/1) configuration, but the settings of software parameters are different.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Sector A Sector B Sector C CDDU CDDU CDDU CMTR CMTR CMTR CMPA CMPA CMPA RF_out RF_out RF_out RF_in RF_in RF_in Sample Sample Sample CMTR...
Page 97
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables (1) M3 screw (2) Lightning protection box (3) Front panel Figure 5-16 Removing front panel of lightning protection box (for E1/T1 cable installation) Determine the positions of waterproof modules for E1/T1 cables led into the cabinet, as shown in Figure 5-17.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables (1) NESP (2) E1/T1 cable (3) Baffle at cable access area (4) Waterproof module Figure 5-18 Routing E1/T1 cables Position the cables and bundle them onto the cabling rack in the cabinet.
Page 99
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables (1) Filling (2) Core layer Figure 5-19 Sealing module Take out the filling when you install cables. You need to put it in the sealing module when you are not using the module to separate cables.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Table 5-4 lists the specifications of these three modules and their functions. Table 5-4 Specifications of common sealing module Available diameter Quantity Type Function of cables (mm)
Page 101
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables (1) Nut after the module is fastened Figure 5-23 Fastening module II. Installation Tools and Installation Requirements To install the waterproof components, you need to use dedicated tools and note the installation requirements.
Page 102
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables – A lot of cable installation positions are reserved in areas 3 and 4. You can lead in the cable through the nearest sealing module.
Remove the same number of layers from the upper half and lower half of each sealing module. If you are using cables provided by Huawei, you can remove the core layers according to Table 5-6. Table 5-6 Cables and number of layers to be removed...
Page 104
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Number of layers Cable Module used to be removed Diameters of these cables are too small. It is recommended you bound Signal cable several cables with the heat-shrinkable tube and route them through the sealing module as one cable.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Table 5-7 Cable diameters and number of layers to be removed Number of Cable diameter layers to be removed 3.5 mm to 4.8 mm 3.2 mm to 5.0 mm 10.0 mm to 11.0 mm...
Page 106
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Use two halves of modules to clamp the cable and fit them together. Reserve a 0.1 mm to 1 mm (0.04 in.) long gap between the two halves of modules, as shown in Figure 5-26.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Insert one half of the module from the bottom of the cabinet. Press the cable against the module and insert the other half of the module and press them with hands.
Page 108
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables (1) M3 screw (2) Shielding clip (3) Waterproof module Figure 5-30 Removing the shielding clip Lead the E1/T1 cable through the waterproof module and press the waterproof module tightly against others by referring to section 5.4.2 "Installing Waterproof...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Caution: Do not leave any silicon gel on the shielding clip or the shielding layer of the E1/T1 cable. Keep the shielding layer intact when peeling off the outer skin of the cable.
"Installing Outdoor Transmission and Power Interface Boxes". After installing transmission cables, attach corresponding labels to cables according to numbers. For details, see Airbridge BTS3606&3606A CDMA Base Station Installation Manual – Installation Reference. 5.4.5 Connecting E1/T1 Trunks to Outdoor Transmission Interface Box Connect the E1/T1 trunks to the outdoor transmission interface boxes of DDF/ODF after laying them out of the cabinet.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Avoid turning while laying optical fibers. Route optical fibers as straight as possible. Lead optical fibers between cabinets through cabling racks, or through the top of cabinets if convenient.
Page 112
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Remove the screws on the GPS lightning arrester. Place the lightning arrester against the groove in the air intake box and fasten it using screws as shown in Figure 5-35.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Install the front panel of the air intake box. Note: The other end of the GPS clock cable is connected to the “ANT” interface on the BCKM.
Page 114
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables (1) Wrong operation—welding (2) Correct operation--connection without (3) To BTS joint welding joint (4) Welding (5) Grounding copper bar or power copper bar Figure 5-37 Wrong and correct operations Caution: If the cable is not long enough, replace a new one.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables black straps and distribute it horizontally or vertically. Bend the cable into a circular arc at the turning point. Stick cables on power cable at 20 mm (0.8 in.) from both ends. For specifications of cable labels, see Chapter 9, “Engineering Labels for Cables”...
Page 116
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables I. Installing Three-Phase Power Cable Caution: Before connecting the power cable, cut off the AC power supply and the battery power supply to ensure the safety.
Page 117
13) Attach engineering labels at the places 20 mm (0.8 in.) to 50 mm (2 in.) away from the lugs on both ends of the power cable. For detailed instructions, see Airbridge BTS3606&3606A CDMA Base Station Installation Manual – Installation Reference.
Page 118
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables 15) Restore the cover of the power lightning protection filter. II. Installing Single-Phase Power Cable When the single-phase power input is used, connect the power cable according to the procedure of installing the three-phase power cable.
Page 119
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables (1) Short-circuit sheet Figure 5-42 Installing short-circuit sheets (2) Note: You can find the short-circuit sheets delivered with the equipment in the tool box of the cabinet.
Page 120
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Figure 5-43 AC power lightning arrester used in the case of two-phase power supply To connect the 110 V two-phase power cable, simply connect the L1, L2 and N lines to the corresponding L1, L2, and N terminals on the lightning arrester.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables 5.8 Installing Cabinet PGND Cables Both ends of the PGND cables for the cabinet are OT terminals (also called lugs). Figure 5-45 shows a PGND cable.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Note: The resistance of the grounding body must accord with the related regulation of the country or the operator’s regulation on communication sites (or radio base station).
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables 5.9 Installing Built-in Batteries Caution: Before connecting the battery cable, turn off the BAT switch in the DC power distribution subrack of the BTS3606A cabinet.
Page 124
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables (1) M3 screw (2) Cover of the battery cabin (3) Battery cabin (4) –48 V cable (5) GND cable (6) Temperature monitoring cable (7) Closing plug...
Page 125
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Place two batteries on the front part of the sliding plate and connect the batteries as show in Figure 5-48. Connect the cable between two batteries.
Page 126
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables The read terminal connects to the positive pole and the black terminal connects to the negative pole. (1) Negative terminal (2) Positive terminal (3) Connection cable between batteries...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables -48V Temperature monitoring cable (1) GND cable (2) Temperature monitoring cable (3) –48 V cable (4) Closing plug Figure 5-51 Connecting the rest cables 11) Apply silicon gel onto the two electric poles connecting the –48 V cable and the GND cable for waterproof purpose.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Table 5-9 Description of cables in battery cabinet Cable name Cable description The positive cable of the battery cabinet is a black GND cable Positive cable of 121 mm (4.76 in.) long.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables (1) The front view (2) The rear view Figure 5-53 Connecting cables in the extended battery cabinet Fasten cables with the socket wrench. Connect cables between the up and down shelves of storage battery modules according to Figure 5-53.
Page 130
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables (1) Wiring terminal (2) Access control sensor cable (3) Access temperature sensor cable (4) Alarm cable (5) –48 V power cable (blue) (6) Black GND cable...
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables Lead the positive cable, the negative cable, the access control and temperature sensor cable, and the grounding cable out of the outlet at the bottom of the cabinet.
Page 132
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables The connection procedure is as follows: Lead the positive cable of the battery cabinet through waterproof components and connect with the GND wiring terminal. Lead the negative cable of the storage battery through waterproof components and connect to the –48 V wiring terminal.
Page 133
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 5 Installing Cables 10) Lead the black grounding cable from the upper part of GND filter to the –48 V GND grounding bar of AC/DC power subrack to complete the installation of grounding cable.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 6 Checking Cabinet Installation Chapter 6 Checking Cabinet Installation 6.1 Check Before Power-on You need to check the installation of the equipment and cables before powering on the BTS3606A.
The transverse cabling part of RF cables are laid inside the cabling trough. The cables are correctly connected according to the cabinet cabling diagram in Airbridge BTS3606&3606A CDMA Base Station Hardware Description Manual. The cables are bound tidily. The interval between cable ties is even. The cables are properly fastened.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 6 Checking Cabinet Installation Check item Redundant part of power cables and grounding cables are cut instead of coiled up. The copper lugs at both ends of the power cable and grounding cable are welded or crimped firmly.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 6 Checking Cabinet Installation PSU0~4 PSU5~8 HX/ACU SPARE S-SOCKET SOCKET Figure 6-1 Front panel of the AC power distribution box Set the multimeter to the voltage scale. Measure the voltage of the socket marked with SOCKET in the AC power distribution box.
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 6 Checking Cabinet Installation Set the multimeter to the voltage scale. Connect the negative pole of the probe to the positive pole (in red) of the battery group, and the positive pole of the probe to the negative (in black) of the battery group.
Page 139
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Chapter 6 Checking Cabinet Installation If any exception condition appears during the process, switch off the power supply immediately. Power on again according to the above procedure after the fault is cleared.
Page 140
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Index Index Numerics 12-core fiber fusing and distributing assembly, 4-10 equipment installation check, 6-1 expansion bolt, 2-9 air breaker air breaker interlock device, 4-3 fastening cabinet, 3-4 diesel air breaker, 4-3...
Page 141
Installation Manual – BTS3606A Cabinet Installation Airbridge BTS3606&3606A CDMA Base Station Index installing outdoor power input component AC/DC unit, 3-15 diesel air breaker assembly, 4-12 DC/DC unit, 3-15 grounding cable for enclosure, 4-13 PMU, 3-15 single-phase mains and diesel input, 4-14...