Save Lens File To/Load Lens File From Memory Card - Panasonic AK-HRP200G Operating Instructions Manual

Setup.Mode.Operations.
3..
Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Do not remove a memory card that is being accessed.
ND
M.GAIN
• To cancel loading, select [n] and press <EXECUTE>.
• The file is loaded from the memory card and [Fin] appears when
loading ends.
• [E02] is displayed if the load operation from the memory card fails.
(→page 20)
If this happens, check the memory card and see whether the file
exists on the memory card. If it does, start over from step 1.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
4.Save.lens.file.to/load.lens.file.from.memory.card
Press.<SELECT>to.select.menu.number.[4].
Select file number,
Save file indication
Select y (Select)/
Load file indication
n (Cancel)
UP
ND
M.GAIN
DATA
SET
DOWN DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
SET UP
SHIFT
+
UP+DOWN SAVE/LOAD
Press to save/load
Press to exit setup mode
(hold down)
4-1.Save.lens.file.to.memory.card
Before switching to setup mode, open the lens file you wish to save with
the ROP menu. (→page 31)
1..
Press.<SAVE/LOAD>.to.select.[ND].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND
M.GAIN
2..
Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
ND
M.GAIN
To save a file to file no. 2 on the memory card
12
(continued)
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC CAMERA
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
3..
Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Do not remove a memory card that is being accessed.
ND
M.GAIN
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
• [E02] is displayed if the save operation to the memory card fails.
(→page 20)
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a lens file with the same name as the one
you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>.(→page 20)
• [E04] is displayed when the lens file is off.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
4-2.Load.lens.file.from.memory.card
1..
Press.<SAVE/LOAD>.to.select.[CC].
• Each press of <SAVE/LOAD> toggles it between [ND] (Save) and
[CC] (Load).
ND
M.GAIN
2..
Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
ND CC
M.GAIN
To load file no. 2 from the memory card
3..
Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Do not remove a memory card that is being accessed.
ND
M.GAIN
• To cancel loading, select [n] and press <EXECUTE>.
• The file is loaded from the memory card and [Fin] appears when
loading ends.
• [E02] is displayed if the load operation from the memory card fails.
(→page 20)
If this happens, check the memory card and see whether the file
exists on the memory card. If it does, start over from step 1.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS