Configuring The Unit Settings [Configuration]; Making Camera Connection Settings [Camera List] - Panasonic AK-HRP200G Operating Instructions Manual

ROP.Setup.software.
(continued)
Configuring.the.Unit.Settings.[Configuration]
Configure the settings of the unit in the [Configuration] tab.
When you connect the personal computer to the unit for the first time,
click the [REFRESH] button (2) to acquire the values set on the unit.
1 3
2 5
1..
Select.the.unit.(ROP).to.be.set.
Click the in the setting target selection list box (1) to display the
IP addresses of ROP units that can be set. From among these, select
the IP address of the ROP you want to set.
Any of the units registered on the [ROP List] tab can be selected.
2..
Update.the.[Configuration].tab.display.
Click the [REFRESH] button (2) to acquire connection information set
to the unit on the personal computer and update the [Configuration]
tab display.
3..
Make.unit.settings.
[SETTING ITEM] (3) is displayed for setting items of the ROP
selected in procedure 1.
Make settings for required items in the [DATA] column (4).
RECEIVE.PORT.
Set the port number for the unit to receive remote camera
configuration file update notifications from remote cameras.
Possible setting range: 35200 to 35599
DISPLAY.BRINGHTNESS.LED.
Set the brightness of the panel LEDs.
DISPLAY.BRIGHTNESS.SEGMENT.DISPLAY.
Set the brightness of the panel 7-segment display.
BUZZER.
Enable or disable the buzzer (beep/call tone).
FLARE/PED.
Select the flare/pedestal control function.
TALLY.ENABLE.
Enable or disable tally output
TALLY.INPUT.
Set which camera is selected for input of tally information to tally
input.
Possible setting range: Cam1 to Cam19
TALLY.CONTROL(Camcoder.only)
Specifies whether tally control is performed via panel operations or
preview terminal inputs.
<Note>.
The settings above can also be made on the unit in setup mode.
4..
Confirm.the.settings.
When the settings are complete, click the [SET] button (5) to confirm
them.
When the [Do you agree to rebooting after data transfer?] message
appears, click the [OK] button.
If you click [CANCEL], the settings are not reflected on the unit.
36
Making.Camera.Connection.Settings.[Camera.List]
On the [Camera List] tab, configure settings for connections between
the ROP and the cameras. When you connect the personal computer to
the unit for the first time, select the ROP to be set in the ROP list box (1)
and click the [REFRESH] button. Values set on the ROP selected in the
4
list box (1) are acquired.
Each of the [C01] to [C19] lines displays a list of the connection setting
information for the corresponding camera number.
5
6
7
8
9
1..
2..
3..
1 4 3 2
12 13
Select.the.ROP.for.which.you.want.to.make.connection.
settings.
Click in the selection list box (1) to display the IP addresses of
ROP units that can be set. From among these, select the ROP whose
IP address you want to set
Any of the units registered on the [ROP List] tab can be selected.
Update.the.[Camera.List].tab.display.
Click the [REFRESH] button (13) to acquire connection information
for the ROP set in the selection list box (1) on the personal computer
and update the [Camera List] tab display.
Make.connection.settings.
Connection setting information is displayed for the ROP selected in
procedure 1.
Make settings for required items.
<NOTE>
Items that can be set and buttons that are enabled/disabled vary
according to the CONNECTION MODE (2) setting.
z With.the.serial.connection.mode .
4 3
5
6
7
CONNECTION.MODE.(2)
Set the connection mode of the selected ROP.
To select the serial connection mode, select the [Serial Mode]
button .
Serial Mode: Make serial mode connection settings.
IP Mode : Make IP connection mode settings.
CAMERA.TYPE.(SERIAL).(3)
Set the device to be connected by serial connection. Select the
connection device.
CCU : Serial connection is used with the CCU.
Remote Camera : Serial connection is used with the remote camera.
Camcoder : Serial connection is used with the camera recorder.
CAMERA.NUMBER.(SERIAL).(4)
Set the camera number of the device to be connected by serial
connections
<NOTE>
These settings are not possible in IP connection mode.
14 15 16
2
10
11