Set Tally Number; Set Tally Output; Syncro Shutter Display Setting; Tally Control Setting (For Camera Recorder Only) - Panasonic AK-HRP200G Operating Instructions Manual

Setup.Mode.Operations.
2..
Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Upgrading starts.
ND
M.GAIN
• When the upgrade ends, [Fin] appears and the unit restarts
automatically.
<Note>
If the upgrade fails for some reason, <SHIFT> may start to flash after
the restart. If this happens, perform the upgrade process again.
20.Set.tally.number
Set the camera number to assign to tally input.
1..
Press.<SELECT>.to.select.menu.number.[20].
Press to select
the camera number
UP
ND
M.GAIN
DATA
SET
DOWN DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
UP+DOWN SAVE/LOAD
Press to exit setup mode (hold down)
2..
Press.<UP>.or.<DOWN>.to.select.a.camera.number.and.
press.<EXECUTE>.to.confirm.the.selection.
ND
M.GAIN
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
21.Set.tally.output
Set the sending of tally information from the unit to remote cameras.
1..
Press.<SELECT>.to.select.menu.number.[21].
Press to select the
camera number
UP
ND
M.GAIN
DATA
SET
DOWN DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
SET UP
SHIFT
+
SAVE/LOAD
UP+DOWN
Press to exit setup mode (hold down)
(continued)
CC SHT SYNC
M.PED
IRIS
Flashes
CC SHT SYNC CAMERA
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS
Flashes
CAMERA
CC SHT SYNC
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number
2..
Press.<UP>.or.<DOWN>.to.select.[on].and.press.
<EXECUTE>.to.confirm.the.selection.
ND
M.GAIN
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
22.Syncro.shutter.display.setting.
Sets whether a camera recorder's syncro shutter speed is displayed in
seconds (SEC) or in iris degrees (DEG).
1..
Press.<SELECT>.to.select.menu.number.22..
Select SEC (seconds) or
DEG (aperture angle)
UP
ND
M.GAIN
DATA
SET
DOWN DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
SET UP
SHIFT
+
SAVE/LOAD
UP+DOWN
Press to exit setup mode (hold down)
2..
Press.<UP>.or.<DOWN>.to.select.[SEC].or.[dEG],.and.
press.<EXECUTE>.to.confirm.the.selection..
ND
M.GAIN
23.Tally.control.setting.(for.camera.recorder.only)
Specifies whether tally control is performed via panel operations or
preview terminal inputs.
1.. Press.<SELECT>.to.select.menu.number.[23].
Select 1 (panel operation)/
2 (preview terminal)
UP
ND
M.GAIN
DATA
SET
DOWN
DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
SAVE/LOAD
UP+DOWN
Press to exit setup mode (hold down)
CC SHT SYNC
M.PED
IRIS
Flashes
CAMERA
CC SHT SYNC
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS
Flashes
CAMERA
CC SHT SYNC
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number
19