ABB ACS560 Quick Installation And Start-Up Manual page 135

conductor.
• Put the connector back onto the terminal post. Start the combi screw, and turn
•
it at least two rotations by hand.
WARNING! Before using tools, make sure that the nut/screw is not cross-
WARNING! Before using tools, make sure that the nut/screw is not cross-
threading. Cross-threading will damage the drive and cause danger.
threading. Cross-threading will damage the drive and cause danger.
• Tighten the combi screw to a torque of 30 N·m (22 lbf·ft). •
11. के व ल फ़् र े म R8: यदि आप समानां त र के ब ल इं स ् ट ाल करते है ं , तो समानां त र पॉवर के ब लों के लिए दू स रा
• Tighten the conductor(s) to 40 N·m (30 lbf·ft) for frame R8 or to 70 N·m •
ग् र ाउं ड िं ग शे ल ् फ इं स ् ट ाल करे ं (11a)। चरण
(52 lbf·ft) for frame R8.
11. Frames R8 If you install parallel cables, install the second grounding shelf for the 11. Frames R8 If you install parallel cables, install the second grounding shelf for the
फ़् र े म R8:
parallel power cables (11a). Repeat steps parallel power cables (11a). Repeat steps
R8 R8
11a
M5×12
12. Install the grounding shelf of the control cables. 12. Install the grounding shelf of the control cables.
12. नियं त ् र ण के ब लों के ग् र ाउं ड िं ग शे ल ् फ को स् थ ापित करे ं ।
90 Electrical installation
90 Electrical installation
13. बिजली के टर् म िनलों पर ढक् क न को पु न र् स ् थ ापित करे ं ।
13. Reinstall the shroud on the power terminals.
13. Reinstall the shroud on the power terminals.
14. यू न िट के बाहर के ब ल् स को यां त ् र िक रू प से सु र क् ष ित करे ं ।
14. Secure the cables outside the unit mechanically.
14. Secure the cables outside the unit mechanically.
12
12
Finalization
15. Ground the motor cable shield at the motor end. For minimum radio frequency
10. Ground the motor cable shield at the motor end. For minimum radio frequency
interference, ground the motor cable shield 360 degrees at the lead-through of
interference, ground the motor cable shield 360 degrees at the lead-through of
15. Ground the motor cable shield at the motor end. For minimum radio frequency
the motor terminal box.
15. मोटर के ब ल शील् ड को मोटर के सिरे पर ग् र ाउं ड कर दे ं । न् य ू न तम रे ड ियो फ् र िक् व े न ् स ी हस् त क् ष े प के लिए,
interference, ground the motor cable shield 360 degrees at the lead-through of
the motor terminal box.
मोटर के ब ल शील् ड को मोटर टर् म िनल बाक् स के लीड-थ् र ू के साथ 360 डिग् र ी पर कने क ् ट करे ं । the motor terminal box.
15
7
15
DC connection
The UDC+ and UDC- terminals (as standard in frames R4...R8) are for using external
brake chopper units.
DC connection
DC कने क ् श न The UDC+ and UDC- terminals (as standard in frames R4...R8) are for using external
brake chopper units.
UDC+ और UDC- टर् म िनल (R4...R8 फ् र े म मे ं मानक अनु स ार) बाहरी ब् र े क चोपर इकाइयों का उपयोग करने
के लिए है ं ।
conductor.
Put the connector back onto the terminal post. Start the combi screw, and turn
it at least two rotations by hand.
Tighten the combi screw to a torque of 30 N·m (22 lbf·ft).
Tighten the conductor(s) to 40 N·m (30 lbf·ft) for frame R8 or to 70 N·m
6...11 (11b) दोहराएं ।
(52 lbf·ft) for frame R8.
6...11 (11b).
R8
M5×25 M5×25
11b 11b
11a
11a
M5×12
13
HI -त् व रित इं स ् ट ाले श न और स् ट ार् ट -अप गाइड 135
6...11 (11b).
R8
11b 11b
11a
13
Electrical installation 81
EN
HI