Sharp AR-FX7 Service Manual page 64

SW67 No. 6 Reduction transmission mode
Used to set whether the transmitted document is received in reduction
size or both ends of recording paper are cut when the transmitted doc-
ument width is greater than the recording paper width.
When set to 1, the document is sent without reduction with the both
ends cut.
When set to "0", it is reduced and transmitted.
Default: 0 (Reduction)
SW67 No. 7 ECM
Used to set whether ECM (Error Correction Mode) is performed or not.
When, however, SW43-1 (V.34 mode function) is set to OFF, or when
SW43-1(V.34 mode function is set to ON and the transmission is not
the super G3 transmission, ECM Disable setup is effective. This is
because the ECM function is indispensable in a transmission other
than super G3 transmission in V.34 mode and the other party machine
may perform checking. With SW43-1 (V.34 mode function) is ON and
this reception function is disabled.
When set to 1, ECM is enabled.
When set to "0", ECM is disabled.
Default: 1 (ECM is enabled)
SW67 No. 8 ECM byte/frame
Used to set ECM byte/frame.
Default: 0 (256 [bytes/frame])
SW68 No.1–No.4 Recording paper tray selection (Tray 1 –
4)
Used to select the tray for output of the received documents.
Tray 1 to Tray 4 can be set to ON/OFF individually. When set to OFF,
the tray does not output received documents.
Setup is made by selecting bit 1 – bit 4. Each bit is selected in the
sequence of tray 1 – tray 4.
When 1 is selected, output is made by using that tray.
When 0 is selected, output is not made by using that tray.
Default: Tray 1 – tray 4 are used. (1)
bit 1 : Tray 1
bit 2 : Tray 2
bit 3 : Tray 3
bit 4 : Tray 4
SW68 No.5–No.8 The tray specification of Duplex print
(Tray 1 – 4)
Used to select the tray for output of the duplex documents.
Tray 1 to Tray 4 can be set to ON/OFF individually. When set to OFF,
the tray does not output received documents.
Setup is made by selecting bit 5 – bit 8. Each bit is selected in the
sequence of tray 1 – tray 4.
When 1 is selected, output is made by using that tray.
When 0 is selected, output is not made by using that tray.
Default: Tray 1 – tray 4 are used. (1)
bit 5 : Tray 1
bit 6 : Tray 2
bit 7 : Tray 3
bit 8 : Tray 4
SW69 No.1, No.2 Reception size specification (Reception
capacity)
Used to set the receivable document width which is notified to the
other party when receiving a document.
The setup items are as follows:
bit 1 2
0 0 : By the equipped cassette
0 1 : B4 (A4, B4)
1 0 : A4
1 1 : A3 (A4, B4, A3)
Default: 0 0 (Varies depending on the installed cassette.)
Max. allowed reception width selection
Max. allowed reception width is determined by Table 1 and Table
2. This determines the transmitted size from the other party.
When set to A3 with SW69-12, only with B5 cassette, proxy recep-
tion is always performed. Do not use this combination. (Because
division process in the main scanning direction is not performed.)
When set to A4 with SW69-12, , A3 document from the other party
is not divided into A4 paper but reduction to A4width is requested
to the other party.
• Max. allowed reception width setup
SW69
No.1 No.2
0
0
1
1
• Max. allowable reception width by installed cassette
[Max. paper size of installed
cassette with FAX function]
No cassette with FAX function
SW69 No. 3 11 inch reception capacity setup
When SW69-12, is set to "Depends on installed cassette," the max.
allowable reception width by 8.5" × 11" cassette is set.
When set to 1, the reception allowable width is 255mm or 215mm.
When set to 0, the reception allowable width is 303mm or 255mm or
215mm.
Default: 0 (the reception allowable width is 303mm or 255mm or
215mm)
SW69 No. 4 Maximum reception length
Used to set the receivable document width which is notified to the
other party when a long document is sent from the other party.
When set to 1, reception is made without limitations.
When set to 0, if reception of a document reaches 1.5m, reception is
terminated.
Default: 0 (Reception is terminated after receiving 1.5m.)
SW69 No.5, No.6 Image quality in transmission request
Used to set the image capacity of the machine when send request
(polling).
Reflected on DTC.
Default: 0 0 (ultra fine)
SW69 No. 7 Countermeasures for echo in reception (CED
tone send interval)
Used to select ON/OFF of countermeasures against echo.
An interval of 500ms is inserted before DIS transmission.
Default: 0 (75ms)
SW69 No. 8 Countermeasure for echo in transmission
(After reception of DIS, hold time up to signal send is set.)
Used to select ON/OFF of countermeasures against echo.
An interval of 500ms is inserted before DCS transmission.
Default: 0 (200ms)
AR-FX7 SOFT SWITCH 7 - 37
Size specification
0 Depends on the
installed cassette.
1 B4
0 A4
1 A3
[Sampled paper size (data
→
→
A5
→
B5
→
A4
→
B4
→
A3
→
Allowable reception
width
Varies according to the
table below.
A4 & B4 width
A4 width
A4 & B4 & A3 width
width)]
A4
B4
A3
B4
A3
A3