Voice 1 - Kenwood TS-890S Instruction Manual

13 VOICE GUIDANCE
Operation on
This Key Operation
Transceiver
Switching of
Turn
quick memory
[MULTI/CH]
channel
Entering a [ENT]
frequency using
the numeric
keypad
Entering a Press a key on
channel number the numeric
using the keypad
numeric keypad
Switching the
Turn
frequency entry
[MULTI/CH]
history
Switching
[LOCK]
frequency lock
Switching split
[SPLIT]
operation
Press and hold
[SPLIT]
When [0] is first
pressed
Configuring split
frequency via
numeric keypad
operation
Numeric keypad
When
configuration of
[SPLIT] (After
the split
configuration
frequency using
using the
the Tuning
Tuning control)
control is
complete
Changing the
Turn [LO/
low cutoff
WIDTH]
frequency
Changing the Turn [LO/
width WIDTH]
Changing the
high cutoff Turn [HI/SHIFT] "High" + Options
frequency
Changing the
Turn [HI/SHIFT] "Shift" + Options
shift frequency
Changing the TX
Turn [POWER]
output power
[MIC/PITCH]
Turn [MIC/
control
PITCH]
operation
13-2
Content of Voice Guidance
Simplex mode:
"Quick" + Number + [A/ B] *1
Frequency + ([X/ R/ XR] + RIT/XIT
Frequency)
*2
Split mode:
"Quick" + Number + "Split" + [A/
B] Frequency + ([X/ R/ XR] +
*1
RIT/XIT Frequency) *2
"Enter"
Numeric value that is entered
Frequency entry history
"Lock" + [On/ Off]
"Split" + [On/ Off]
"Split" + "Enter"
"Minus"
"TX" + [Plus/ Minus] * + Numeric
value that is entered + "Kilohertz"
* Pressing the keys from [1] to [9]
adds a "Plus" utterance, while
pressing [0] + ([1] to [9]) adds a
"Minus" utterance.
"TX" + Finalized TX frequency
"Low" + Frequency
"Width" + Options
• When drive output is ON: TX
power + Value
• When drive output is OFF:
When the transverter is ON and "TX
Power Down with Transverter
Enabled" is "On": "TX power" + 5
In all other cases: "TX power" +
Value (The value shows a value up
to the TX output power limit if the TX
output power limiter is operating.)
• When adjusting microphone
gain: "Mic. Gain" + Value
• When adjusting the speech
processor output level:
"Processor"+ "Out" + Value
* No voice is output during
adjustment of the sidetone/pitch
frequency.
Operation on
This Key Operation
Transceiver
[DELAY] control
Turn [DELAY]
operation
[KEY] control
Turn [KEY]
operation
Timer function
ON/OFF F [TIMER]
operation
Dimmer F [DIMMER]
switching F2 [DIMMER]
Antenna
F [ANT]
switching
Band Direct
Band Direct keys (including
selection operation of
[GENE])
Calling up the
preconfigured PF [Emergency
emergency Frequency]
frequency
Meter switching F [METER]
Error/warning
(none)
messages

Voice 1

Voice 1 announces the displayed frequency, channel number,
details of the respective configuration modes as well as the status
of menu settings.
Announces the digits of the VFO and memory channel frequencies
which are higher than 10 Hz when fine tuning is OFF. "Point" is
uttered after announcing the MHz digits. When a channel that does
not contain any operating data is selected during memory scroll,
"Blank" is uttered.
Press the PF key that is assigned with "VOICE1".
Announces the operating status. Announces the setting value
while configuration is in progress on the configuration screen.
Pressing the PF key that is assigned with "VOICE1",
●
"VOICE2" or "VOICE3" during the announcement stops
the announcement.
Altering the frequency by turning the Tuning or [MULTI/
●
CH] control during an announcement stops the
announcement.
For more details on how to change the assignment of PF
●
keys, please refer to
Keys)" (16-2).
Announcement is not output while scanning is in
●
progress.
Content of Voice Guidance
• When adjusting the break-in
delay time: "Full" + "Break-in" in
the case of FULL-BK
DELAY: "Break-in delay" +
Displayed value in the case of 1 to
20
• When adjusting VOX delay:
"VOX delay" + Value
• When adjusting the keying
speed: Keying speed + Value
"Timer" + [On/ Off]
"D" + Numeric value (single digit)
"Antenna" + Number
Frequency
"Emergency" + Frequency
Analog meter display (TX digital
meter OFF): [Power/ SWR/ ID/
Processor/ ALC/ VD]
Analog meter display (TX digital
meter ON): [SWR/ ID/ Processor/
VD/ TMP]
Digital meter display: [SWR/ ID/
Processor/ VD/ TMP]
Mini digital meter display: [Power/
SWR/ ID/ Processor/ ALC/ VD/
TMP]
Error or warning + Number
* For more details on the number,
please refer to "Error Messages"
(18-9) and "Warning Messages"
(18-11).
"PF Keys (Programmable Function