Panasonic AV-HS6000 Series Operation Manual page 48

2
Turn on the power of the Control Panel AV‑HS60C1/AV‑HS60C2/AV‑HS60C4 while pressing the <KEY1> button, <KEY4> button,
and <KEY1 TRNS> button in the KEY operation section of the ME line at the top.
The Control Panel AV-HS60C1/AV-HS60C2/AV-HS60C4 is booted in the network setting mode.
Part of the status display and the source display in the ME line at the top will become as follows when it goes into the network setting mode.
f Status display: Setting item is displayed.
The setting item is switched every time the <AUTO> button in the ME line at the top is pressed.
Display
IP
MSK
GTW
MIP
f Source display: Setting value is displayed.
The value will increase by pressing the A bus XPT button under the setting value.
The value will decrease by pressing the B bus XPT button under the setting value.
3
Set each item.
Change the setting value for each setting item, and confirm by pressing the <CUT> button in the ME line at the top.
f The <CUT> button will light up in green when the setting is correctly made.
f The <CUT> button will light up in red when the setting is not correctly made.
f The changed setting value is not confirmed when the setting item is switched without pressing the <CUT> button.
f When the value of the IP address is changed and the <CUT> button is pressed, the value is checked against the value of the subnet mask. At this
time, if the binary of the host address is changed to 0 or 1, the changed value is not confirmed. The <CUT> button lights up in red. In this case,
change the value of the subnet mask, and then change the value of the IP address.
4
Turn off the power of the Control Panel AV‑HS60C1/AV‑HS60C2/AV‑HS60C4.
@ NOTE
t For the subnet mask, use the same address as the address set for the <LAN> terminal of the Main Frame AV-HS60U1/AV-HS60U2.
t Set the IP address that does not overlap with the following IP address.
- The IP address set to other device that is connected to the <LAN> terminal of the Main Frame AV-HS60U1/AV-HS60U2
- The IP address set for the <LAN> terminal of the Main Frame AV-HS60U1/AV-HS60U2
t If the default setting for the <LAN> terminal of the Main Frame AV-HS60U1/AV-HS60U2 is not changed, it can be connected as the sub control panel
when the value described in the setting example is set.
t For details on the network setting for the <LAN> terminal of the Main Frame AV‑HS60U1/AV‑HS60U2, refer to "Configuring the network for the Main
Frame AV-HS60U1/AV-HS60U2" (page 48).
Configuring the network for the Main Frame AV‑HS60U1/AV‑HS60U2
Configure the network for the <LAN> terminal of the Main Frame AV‑HS60U1/AV‑HS60U2.
f The default setting is as follows: IP address: 192.168.0.5, subnet mask: 255.255.255.0, default gateway: No setting
1
Select the <SYS> button → [SYSTEM] → [Network] tab.
2
Set [IP Address] and [Subnet Mask] in the [Network1] column.
[IP Address]
[Subnet Mask]
f When the value of the IP address is changed, the value is checked against the value of the subnet mask. At this time, if the binary of the host
address is changed to 0 or 1, the changed value is not confirmed. In this case, change the value of the subnet mask, and then change the value of
the IP address.
3
Set/check [Default Gateway] and [MAC Address] in the [Network2] column.
[Default Gateway]
[MAC Address]
4
Select the <SYS> button → [CTRL PANEL] → [SubPanel1] tab → [Network] column, and set the IP address of the sub control
panel 1 to be connected.
[IP Address]: Sets the IP address of the sub control panel 1 to be connected. (Setting example: 192.168.0.8)
Set this only when the sub control panel is connected.
5
Select the <SYS> button → [CTRL PANEL] → [SubPanel2] tab → [Network] column, and set the IP address of the sub control
panel 2 to be connected.
[IP Address]: Sets the IP address of the sub control panel 2 to be connected. (Setting example: 192.168.0.9)
Set this only when the sub control panel is connected.
@ NOTE
t A network with the IP address between 10.0.0.0 and 10.0.0.7 is used for the <PANEL> terminal of the Main Frame AV-HS60U1/AV-HS60U2. The
setting cannot be changed.
t The <LAN> terminal of the Main Frame AV-HS60U1/AV-HS60U2 cannot be connected to a network containing the IP address between 10.0.0.0 and
10.0.0.7. Do not configure the setting of sub network containing the IP address between 10.0.0.0 and 10.0.0.7.
Chapter 4 Preparations — Various settings
IP address
Subnet mask
Default gateway
IP address of the connecting Main Frame AV-HS60U1/AV-HS60U2
Sets the IP address. (Setting example: 192.168.0.5)
Sets the subnet mask. (Setting example: 255.255.255.0)
Sets the default gateway.
Checks the MAC address.
Setting item
– 48 –
Setting example
192.168.0.8
255.255.255.0
0.0.0.0
192.168.0.5