Panasonic AV-HS6000 Series Operation Manual page 74

Setting the trimming
Set the trimming type and values as well as operation for when manual is set. The default setting is as shown in the following figure.
1
Select the <ME1>/<ME2> button → [KEY1] to [KEY4] → [PinP Adjust] tab.
2
Select an item in [Trim] in the [Trim] column.
[Off]
[4:3]
[Manual]
3
Select an item in [Manual] in the [Trim] column.
[Free]
[Pair]
4
Set [Left], [Top], [Right], and [Bottom] in [Trim Adjust1]/[Trim Adjust2].
f Set the trimming value. The [Left] setting cannot exceed the [Right] setting (and vice versa), and the [Top] setting cannot exceed the [Bottom]
setting (and vice versa).
[Left]
[Top]
[Right]
[Bottom]
5
Set [WipeAspect] in the [Trim] column.
f The aspect ration of the wipe pattern is changed when anything other than [Off] is selected in [WipeMask] in the [Mode] column.
Copying the PinP setting
The setting for PinP can be copied.
1
Select the <ME1>/<ME2> button → [MISC] → [Misc] tab.
2
Select an item in [Key1 From] to [Key4 From] in the [PinP Copy] column.
f Select the channel of the key to be the copy source of the PinP setting.
3
Select [Execute] in the [PinP Copy] column.
f Following the setting in Step
f Settings inside the <ME1>/<ME2> button → [KEY1] to [KEY4] → [PinP Adjust] are copied.
However, the settings of [Sync] and [Sync Mode] in the [Mode] column are not copied.
f The copy is not executed to the channel of the key set to [No Assign] in Step
Wipe transition of PinP
SQ or SL can be set as the wipe transition effect when PinP is enabled.
The settings other than the wipe transition effect are the same as when PinP is disabled. Refer to "Setting the key transition mode" (page 63).
r Setting the wipe transition of PinP
1
Select the <ME1>/<ME2> button → [KEY1] to [KEY4] → [Key Pattern] tab.
2
Select an item in [PinP Wipe Mode] of the [Key Pattern] column.
[Off]
[SQ]
[SL]
3
Set [X‑Pos] and [Y‑Pos] in the [In Position] column.
Chapter 5 Basic Operations — KEY
[50]
[40]
[Top]
[0]
[Bottom] [−40]
[−50]
[−50]
[−40]
[Left]
Does not perform trimming.
Trims automatically so that the aspect ratio is 4:3.
Trims using the values set with [Trim Adjust1] and [Trim Adjust2].
Sets the amount of trimming for [Left], [Right], [Top], and [Bottom] separately.
Changes the settings in such a way that the [Left] and [Right] trimming amounts, and the [Top] and [Bottom] trimming
amounts are the same. (This makes for a top-bottom and left-right symmetry.)
Sets the left trimming value.
Sets the top trimming value.
Sets the right trimming value.
Sets the bottom trimming value.
2
, settings of the PinP for each key are copied.
Transitions with cut, mix.
Transitions from size 0 to size specified in the [PinP Adjust] tab → [Position] column → [Size].
Transitions while moving without changing the size specified in the [PinP Adjust] tab → [Position] column → [Size]. It will
key on/key off with the cut operation.
Area trimmed
PinP effective area
Original size of PinP
[0] [50]
[40]
[Right]
2
.
– 74 –