Dell 0G8DW Installation And Service Manual page 59

Option Description
I/OAT DMA Engine Enables or disables the I/O Acceleration Technology (I/OAT) option. I/OAT is a set of DMA features designed to
accelerate network traffic and lower CPU utilization. Enable only if the hardware and software support the
feature.This option is set to Disabled by default.
Embedded Video Enables or disables the use of Embedded Video Controller as the primary display. When set to Enabled, the
Controller Embedded Video Controller is used as the primary display even if add-in graphic cards are installed. When set to
Disabled, an add-in graphics card is used as the primary display. BIOS will output displays to both the primary add-
in video and the embedded video during POST and pre-boot environment. The embedded video is disabled before
the operating system boots. This option is set to Enabled by default.
Current State of Displays the current state of the embedded video controller. The Current State of Embedded Video Controller
Embedded Video option is a read-only field. If the Embedded Video Controller is the only display capability in the system (that is, no
Controller add-in graphics card is installed), then the Embedded Video Controller is automatically used as the primary display
even if the Embedded Video Controller setting is set to Enabled.
SR-IOV Global Enables or disables the BIOS configuration of Single Root I/O Virtualization (SR-IOV) devices. This option is set to
Enable Disabled by default.
Internal SD Card Enables or disables the internal SD card port of the Internal Dual SD Module (IDSDM). This option is set to On by
Port default.
Internal SD Card Configures the redundancy mode of the Internal Dual SD Module (IDSDM). When set to Mirror Mode, data is
Redundancy written on both SD cards. After failure of either card and replacement of the failed card, the data of the active card
is copied to the offline card during the system boot.
When Internal SD Card Redundancy is set to Disabled, only the primary SD card is visible to the OS. This option is
set to Disabled by default.
Internal SD Primary By default, the primary SD card is selected to be SD Card 1. If SD Card 1 is not present, then the controller selects
Card SD Card 2 to be the primary SD card.
OS Watchdog If your system stops responding, this watchdog timer aids in the recovery of your operating system. When this
Timer option is set to Enabled, the operating system initializes the timer. When this option is set to Disabled (the
default), the timer does not have any effect on the system.
Memory Mapped Enables or disables the support for the PCIe devices that need large amounts of memory. Enable this option only
I/O above 4 GB for 64-bit operating systems. This option is set to Enabled by default.
Memory Mapped When set to 12 TB, the system maps the MMIO base to 12 TB. Enable this option for an OS that requires 44 bit
I/O Base PCIe addressing. When set to 512 GB, the system maps the MMIO base to 512 GB, and reduces the maximum
support for memory to less than 512 GB. Enable this option only for the 4 GPU DGMA issue. This option is set to
56 TB by default.
Slot Disablement Enables or disables the available PCIe slots on your system. The slot disablement feature controls the configuration
of the PCIe cards installed in the specified slot. Slots must be disabled only when the installed peripheral card
prevents booting into the operating system or causes delays in system startup. If the slot is disabled, both the
Option ROM and UEFI drivers are disabled. Only slots that are present on the system are available for control.
Table 40. Slot Disablement
Option
Slot 1
Slot Bifurcation Allows Platform Default Bifurcation, Auto discovery of Bifurcation and Manual bifurcation Control. The default
is set to Platform Default Bifurcation. The slot bifurcation field is accessible when set to Manual bifurcation
Control and is disabled when set to Platform Default Bifurcation or Auto discovery of Bifurcation.
NOTE: When there are multiple add-in graphic cards installed in the system, the first card discovered
during PCI enumeration is selected as the primary video. You might have to re-arrange the cards in the
slots in order to control which card is the primary video.
Description
Enables or disables the PCIe slot 1. This option is set to
Enabled by default.
Pre-operating system management applications 59