Series Programs - Toshiba Strata CIX Programming Manual

300 Series Programs

Table 1-26 Programs 300~302
Button Sequence
300 Trunk Assignment
300 Hold
,
300-00 Line Number
Hold
n,
300-01 Line Equipment No.
FB01 Hold
, xxyyzz,
300-02 Incoming Line Group
FB02 Hold
, n,
300-03 Outgoing Line Group
FB03 Hold
, n,
300-04 Dial Mode
FB04 Hold
, n,
300-05 Signaling
FB05 Hold
, n,
300-06 Start Method
FB06 Hold
, n,
300-07 Release Supervision
FB07 Hold
, n,
300-08 Answer Supervision
FB08 Hold
, n,
300-09 Trunk Name
300-10 External Ring Repeat
FB10 Hold
, n,
Strata CIX/CTX Telephone Button Programming 11/04
Value(s)
n = 1~64 (CTX100)
1~96 (CTX670 Basic)
1~264 (CTX670 Exp.)
xx = Cabinet 1 (CTX100),
01~02 (CTX670 Basic),
01~07 (CTX670 Exp.)
yy = Slot 01~8 (CTX100),
01~10 (CTX670)
zz = Circuit (01~04)
Ö or zz = T1 Circuit 01~24
(CTX670).
n = 0~32 (CTX100)
0~50 (CTX670 Basic)
0~128 (CTX670 Exp.)
(default = 0)
n = 0~32 (CTX100)
0~50 (CTX670 Basic)
0~128 (CTX670 Exp.)
(default = 0)
n = 1. Rotary Dial 10PPS
2. Rotary Dial 20PPS
3. DTMF (default)
n = 1. DID
2. Loop (default)
3. Ground
4. Tie
5. LP (Japan)
6. SR (Japan)
7. ACU (UK)
n = 1. Immediate Start
(default)
2. Timing Start
3. Wink Start
n = 1. Received
2. Not Received (default)
n = 1. Received
2. Not Received (default)
n = Up to 14 digits
n = 1. Supplied (default)
2. Not Supplied
Telephone Button Programming
Summary
This command assigns an analog or T1 trunk (line) and its
parameters to the system.
Enter the Line Number.
Enter the line equipment number as xxyyzz. Equipment numbers are
required when assigning a new trunk to the system. It can also be
used to display the equipment location of existing trunks.
Example: If the trunk should be connected to an RCOU in cabinet
shelf 5, slot 2, circuit 3, enter 050203.
Cabinet numbers:
•
CTX100 ñ Select 01 for Base and Expansion cabinet.
•
CTX670 ñ Select 01 for Base and 02~07 respectively for each
Expansion cabinet.
Slot numbers:
•
CTX100 ñ Select 01~04 for Base slots and 05~08 for Expansion
slots.
•
CTX670 ñ Select 01~08 for Base slots and 01~10 for Expansion
slots.
Assign the trunk to Incoming Line Group. Two-way trunks need to be
members of one incoming and one outgoing line group.
Assign the trunk to Outgoing Line Group. Two-way trunks need to be
members of one incoming and one outgoing line group.
Enter the Dial Mode.
•
DP 10 PPS = Rotary Dial, 10 PPS
•
DP 20 PPS = Rotary Dial, 20 PPS
Enter the signalling type.
Enter the Start Method. This setting defines the start protocol method
used between the PSTN and this trunk. For DID/Tie trunks.
Enable Release Supervision from the CO.
Enable Answer Supervision from the CO.
Enter the trunk name.
Note This function is accessible only through CTX WinAdmin.
Supply the External Ringing Signal pattern to stations. For behind
PBX/Centrex trunks.
300 Series Programs
1-53