Toshiba Strata CIX Programming Manual page 59

Table 1-26 Programs 300~302 (continued)
Button Sequence
302-06 Trunk ID Number
FB06 Hold
, n,
302-07 D Ch Position
FB07 Hold
, n,
302- Bearer Services:
08~13
•
Speech
•
3.1 KHz Audio
•
7 KHz Audio
•
Unrestr. 64K
•
Unrestr. 56K
•
Unrestr. 2x64K
FB08 FB13 Spkr
~ , n,
Hold
n1,
302- Bearer Services:
14~18
•
Unrestr. 384K
•
Unrestr. 1536K
•
Unrestr. 1920K
•
Restr. Digital
•
Video
FB14 FB18 Spkr
~ , n,
Hold
n1,
302-19 Bearer Service
Multirate Unrestricted
FB19 Hold
, n,
302-20 B Ch Selection
Method
FB20 Hold
, n,
302-21 B Ch Selection
FB21 Hold
, n,
302-22 T1 Time Slot Pattern
FB22 Hold
, n,
302-23 E1 Time Slot Pattern
FB23 Hold
, n,
302-24 T-Wait Timer
FB24 Hold
, n,
302-25 RBT on Incoming Call
FB25 Hold
, n,
302-26 Network Mode
FB26 Hold
, n,
302-27 Negotiation Priority
FB27 Hold
, n,
Strata CIX/CTX Telephone Button Programming 11/04
Value(s)
n = 0~126
(default = 0)
n = 1~24
(default = 24)
n = 1. Enable
2. Disable
n1 = 1. Channel Number
2. Slot Map
,
n = 1. Enable
2. Disable (default)
n1 = 1. Channel Number B
2. Channel Number H
3. Slot Map B
,
4. Slot Map H
n = 1. Enable
2. Disable (default)
n = 1. Exclusive
2. Preferred
3. Any
n1 = 1. Forward Cyclic
2. Backward Cyclic
3. Forward Terminal
4. Backward Terminal
n = 1. Fixed1 (default)
2. Fixed2
3. Flexible
n = 1. Fixed1 (default)
2. Fixed2
3. Flexible
n = 1. Enable
2. Disable (default)
n = 1. Enable (default)
2. Disable
n = 1. Master
2. Slave (default)
n = 1. Side A (default)
2. Side B
Telephone Button Programming
Summary
An identifier must be used as part of the addressing when an ìexplicitî
identified is used to communicate with the PSTN which channel on
which link is used for the given call. This identifier is assigned by the
connected PSTN.
PRI includes a 64-kbps D-channel (for transfer of signal information).
Select the channel position to be used for D channel signaling.
Note This field is used only when the span interface speed is 1.5M.
If the span interface speed is 2M the value is fixed at 16.
Enable the Bearer Capabilities allowed for this PRI Trunk channel
group.
Select the Channel Method (map) to identify the channels.
Note In North America, only Channel Number map is used
(Channel Number).
The Bearer Capabilities (384k Unrestricted(H0), 1536k
Unrestricted(H11), 1920k Unrestricted, Restricted Digital Info, Trunk
Video, and Unrestricted Multirate) are not used and should remain
disabled.
Select the Channel Method (map) to identify the channels.
Note In North America, only Channel Number B map is used.
The Bearer Capabilities 384k Unrestricted (H0), 1536k Unrestricted
(H11), 1920k Unrestricted, Restricted Digital Info, Trunk Video and
Unrestricted Multirate are not used and should remain disabled.
The method used for selecting an idle ë Bí channel and the reaction if
the PSTN indicates the channel is not available needs to be chosen to
originate a call from CTX.
Preferred option is recommended, unless PSTN needs other choice.
The search method for choosing an idle ë Bí channel shall also be
specified. Backward Terminal is the normal method with the PSTN
following a Forward Terminal method.
1544 Time Slot Pattern.
2048 Time Slot Pattern.
Specify whether the T-Wait timer is to be enabled or disabled. This
field is only valid for Natíl ISDN.
Enable Ringback Tone when terminating a call. This field is only valid
for Natíl ISDN.
Set this span as Master or Slave for Layer 2 of a QSIG PRI. The
opposite value must be set for the node in which this QSIG PRI
terminates. This governs call setup activity and is not related to clock
synchronization.
Sets this span as Side A or Side B for Layer 3 of a QSIG PRI. The
opposite value must be set for the node in which this QSIG PRI
terminates.
300 Series Programs
1-55