Siemens SINUMERIK 828D Function Manual page 135

Table 2-3 Protection zone: Workpiece and tool holder
System variable
$SN_PA_ACTIV_IMMED[0]
$SN_PA_ACTIV_IMMED[1]
$SC_PA_TW[0]
$SC_PA_TW[1]
$SC_PA_ORI[0]
$SC_PA_ORI[1]
$SC_PA_LIM_3DIM[0]
$SC_PA_LIM_3DIM[1]
$SC_PA_PLUS_LIM[0]
$SC_PA_PLUS_LIM[1]
$SC_PA_MINUS_LIM[0]
$SC_PA_MINUS_LIM[1]
$SC_PA_CONT_NUM[0]
$SC_PA_CONT_NUM[1]
$SN_PA_CONT_TYP[0,0]
$SN_PA_CONT_TYP[0,1]
$SN_PA_CONT_TYP[0,2]
$SN_PA_CONT_TYP[0,3]
$SN_PA_CONT_TYP[0,4]
$SN_PA_CONT_TYP[0,5]
$SN_PA_CONT_TYP[0,6]
$SN_PA_CONT_TYP[0,7]
$SN_PA_CONT_TYP[0,8]
Basic Functions
Function Manual, 09/2011, 6FC5397-0BP40-2BA0
Valu Comment
e
0 ; Protection zone for workpiece not immediately active
0 ; Protection zone for tool holder not immediately active
" " ; Protection zone for workpiece, channel-specific
'H01' ; Protection zone for toolholder, channel-specific
1 ; Orientation of the protection zone: 1= 3. and first geometry
axis
; Protection zone for workpiece
1 ; Orientation of the protection zone: 1= 3. and first geometry
axis
; Protection zone for tool holder
0 ; Type of limitation in the third dimension: 0 = no limitation
; Protection zone for workpiece tool holder 0
0 ; Type of limitation in the third dimension: 0 = no limitation
; Protection zone for tool holder
0 ; Value of limitation in positive direction in the third dimension
; Protection zone for workpiece
0 ; Value of limitation in positive direction in the third dimension
; Protection zone for tool holder
0 ; Value of limitation in negative direction in the third dimension
; Protection zone for workpiece
0 ; Value of limitation in negative direction in the third dimension
; Protection zone for tool holder
4 ; Number of valid contour elements,
; Protection zone for workpiece
5 ; Number of valid contour elements,
; Protection zone for tool holder 1
1 ; Contour type[i] : 1 = G1 for even,
; Protection zone for workpiece, contour element 0
1 ; Contour type[i] : 1 = G1 for even,
; Protection zone for workpiece, contour element 1
1 ; Contour type[i] : 1 = G1 for even,
; Protection zone for workpiece, contour element 2
1 ; Contour type[i] : 1 = G1 for even,
; Protection zone for workpiece, contour element 3
1 ; Contour type[i] : 1 = G1 for even,
; Protection zone for workpiece, contour element 4
0 ; Contour type[i] : 0 = not defined,
; Protection zone for workpiece, contour element 5
0 ; Contour type[i] : 0 = not defined,
; Protection zone for workpiece, contour element 6
0 ; Contour type[i] : 0 = not defined,
; Protection zone for workpiece, contour element 7
0 ; Contour type[i] : 0 = not defined,
; Protection zone for workpiece, contour element 8
A3: Axis Monitoring, Protection Zones
2.5 Examples
135