Panasonic VariCam LT Operating Manual page 140

Item
[SYS CHECK]
[TOGGLE]
[PLAYBACK SETTING] [PLAYBACK MODE]
[CARDS/MEDIA] [FORMAT MEDIA]
[MEDIA END ALARM]
[POWER [DC IN SOURCE]
MANAGEMENT]
[DC IN BATTERY
SETTINGS]
[- FULL VOLT]
[- NEAR END VOLT]
[- END VOLT]
[ONBOARD BATTERY
SETTINGS]
[- BATTERY SELECT]
[- FULL VOLT]
[- NEAR END VOLT]
[- END VOLT]
[- NEAR END INFO]
[- END INFO]
[END ALARM]
Chapter 10 Menu Operations — Menu list
Sets if the <SYSTEM CHK> button is to be locked or not with the <LOCK> switch on the camera.
[LOCK]: It will be locked.
[UNLOCK]: It will not be locked.
f Factory setting: [LOCK]
Sets if the <TOGGLE/WB> is to be locked or not with the <LOCK> switch on the camera.
[LOCK]: It will be locked.
[UNLOCK]: It will not be locked.
f Factory setting: [LOCK]
Specifies the playback mode of the PLAY screen.
[SINGLE]: Plays back only the clip in the cursor position.
[CONTINUOUS]: Continuously plays back the clips in the list.
f Factory setting: [SINGLE]
Formats the card in the specified slot after the format menu is selected.
[MAIN SLOT], [SUB SLOT]
Data deleted as a result of formatting cannot be restored. Always check the data before formatting.
Sets if the alarm is to be sounded when there is no remaining capacity in the memory card.
[ON], [OFF]
f Factory setting: [ON]
Sets the type of the external power supply input into the <DC IN> terminal.
[DC POWER SUPPLY]: Selected when connecting an AC adaptor. In this case, the remaining battery
charge level is not displayed.
[BATTERY]: Selected when connecting a battery to the <DC IN> terminal. Remaining charge level is
detected from the voltage level.
f Factory setting: [DC POWER SUPPLY]
Following items are settings for the external battery connected to the <DC IN> terminal.
Sets the voltage to be displayed in the remaining charge level full display when an external battery is input
from the <DC IN> terminal.
[13.0V] - [17.0V] (0.1 V step)
f Factory setting: [15.5V]
Sets the remaining charge level near end voltage when an external battery is input from the <DC IN>
terminal.
[11.0V] - [15.0V] (0.1 V step)
f Factory setting: [13.2V]
Sets the remaining charge level end voltage when an external battery is input from the <DC IN> terminal.
[11.0V] - [15.0V] (0.1 V step)
f Factory setting: [12.5V]
Following items are settings for the external battery connected to the battery holder.
Selected according to the battery used.
[DIONIC], [HyTRON], [ENDURA], [PAG]: The remaining charge level is detected and a warning is
displayed according to the [- NEAR END INFO] and [- END VOLT] settings. When there is no remaining
charge level information, the remaining charge level is detected from the voltage level.
[other]: Remaining charge level is detected from the voltage level.
f Factory setting: [DIONIC]
Sets the voltage in the remaining charge level full display when the battery remaining charge level is
detected from the voltage level.
[13.0V] - [17.0V] (0.1 V step)
f Factory setting: [15.5V]
Sets the remaining charge level near end voltage when the battery remaining charge level is detected from
the voltage level.
[11.0V] - [15.0V] (0.1 V step)
f Factory setting: [13.2V]
Sets the remaining charge level end voltage when the battery remaining charge level is detected from the
voltage level.
[11.0V] - [15.0V] (0.1 V step)
f Factory setting: [12.5V]
Sets the percentage value of the remaining charge level near end when remaining charge level information
is acquired from the battery.
[4%], [5%], [6%], [7%], [8%], [9%], [10%], [12%], [14%], [16%], [18%], [20%]
f Factory setting: [5%]
Sets the percentage value of the remaining charge level end when remaining charge level information is
acquired from the battery.
[1%] - [10%] (1% step)
f Factory setting: [1%]
Sets whether to sound an alarm at battery remaining charge level end.
[ON], [OFF]
f Factory setting: [ON]
– 140 –
Description of settings