Panasonic VariCam LT Operating Manual page 143

Item
[GAIN SELECT]
[SHUTTER] [SW]
[DISPLAY MODE]
[VALUE deg]
[VALUE sec]
[ADD deg]
[ADD sec]
[DELETE deg]
[DELETE sec]
[LENS SETTING] [LENS CONNECT
TYPE]
[A.IRIS TYPE]
[A.IRIS SPEED]
[A.IRIS LEVEL EFFECT] Sets the target value during auto iris operation.
[A.IRIS WINDOW]
[A.IRIS PEAK/AVE]
[ONE PUSH A. IRIS]
[EF LENS IRIS MODE]
[GRIP IRIS]
Chapter 10 Menu Operations — Menu list
Sets the value when [dB] is selected.
[−12dB], [−10dB], [−8dB], [−6dB], [−4dB], [−2dB], [0dB], [2dB], [4dB], [6dB], [8dB], [10dB], [12dB],
[14dB]
When [GAMMA] → [GAMMA SELECT] is set to [VIDEO45]/[VIDEO50]/[BC GAMMA].
This will be set to [−6dB], [−4dB], [−2dB], [0dB], [2dB], [4dB], [6dB], [8dB], [10dB], [12dB], [14dB], [16dB],
[18dB], or [20dB].
This will be [−6dB], [−4dB], [−2dB], [0dB], [2dB], [4dB], [6dB], [8dB], [10dB], [12dB], or [14dB] when [MAIN
CODEC] is set to [AVC-Intra2K-LT]/[AVC-Intra-LT], and [MAIN PIXEL] is set to [2048×1080 CROP]/
[1920×1080 CROP].
f Factory setting: [0dB]
Enables/disables the shutter function.
[ON], [OFF]
f Factory setting: [ON]
Sets the shutter display unit.
[sec]: Displays in time.
[deg]: Displays at shutter open angle.
f Factory setting: [deg]
Selects the angle control ([deg]) value from the maximum of 12 registered values.
Preset values that can be selected in the factory settings are [11.5d], [22.5d], [45.0d], [90.0d], [120.0d],
[144.0d], [172.8d], [180.0d], [270.0d], and [358.0d].
f Factory setting: [180.0d]
Selects the time control ([sec]) value from the maximum of 12 registered values.
Preset values that can be selected in the factory settings are [1/60.0], [1/100.0], [1/120.0], [1/250], [1/500],
[1/1000], and [1/2000].
f Factory setting: [1/60.0]
Newly registers the angle control ([deg]) value to the list.
Newly registered value can be selected with [VALUE].
It will replace the currently selected value when there are 12 numbers registered already.
Newly registers the time control ([sec]) value to the list.
Newly registered value can be selected with [VALUE].
It will replace the currently selected value when there are 12 numbers registered already.
Deletes the angle control ([deg]) value from the list.
Deletion is not possible when there is only one registered value.
[YES], [NO]
Deletes the time control ([sec]) value from the list.
Deletion is not possible when there is only one registered value.
[YES], [NO]
Sets the type of lens to be connected.
[EF]: Lens controlled with EF
[LDS]: Lens controlled with LDS (Lens Data System)
[B4]: Lens controlled with 12-pin connector
[Cooke-i]: Lens controlled with cooke/i communication
[OFF]: Other lenses
f Factory setting: [EF]
Sets the location to control the speed of the auto iris when [LENS CONNECT TYPE] is set to [B4].
[LENS]: Lens volume
[CAM]: Set with [A.IRIS SPEED]
f Factory setting: [LENS]
Sets the speed of the auto iris when [LENS CONNECT TYPE] is set to [B4] and [A.IRIS TYPE] is set to
[CAM].
[1] - [20]
f Factory setting: [10]
[0] - [100]
f Factory setting: [50]
Selects the auto iris detection window.
[NORMAL1]: Window that is near screen center.
[NORMAL2]: Window that is near screen bottom.
[CENTER]: Window that is a spot in the screen center.
f Factory setting: [NORMAL1]
Sets the ratio included in the peak for auto iris standard.
[0] - [100]
f Factory setting: [30]
Executes the one-push auto iris.
[EXECUTE], [CANCEL]
Sets the operation of the iris when [EF] is selected.
[MANUAL]: Manual control
[AUTO]: Auto control
f Factory setting: [MANUAL]
Sets the turning direction of the <IRIS> dial and the iris control of the grip module.
[RIGHT OPEN]: The iris will open when the <IRIS> dial is turned clockwise.
[LEFT OPEN]: The iris will open when the <IRIS> dial is turned counterclockwise.
f Factory setting: [RIGHT OPEN]
– 143 –
Description of settings